IVEN:A 20-ft beam is subjected to the distributed load show.0.75 in. 6 in.-3 kip/ctABK-8ft →→ 12 ftSOLUTION:TOT12 in.BeamCrossSection 0.75 in-0.5 in.ASBFIND:a. The bending stress at A.b. The bending stress at B.

Answered: Image /qna-images/answer/dd2c3925-d2a5-44c0-9dbe-4dace51fc1b7.jpg

A 20-ft beam is subjected to the distributed load show. 0.75 in. -3 kip/ct A B K8 ft →→ 12 ft- UTION: D TOT 12 in. Beam Cross Section 0.75 in. -0.5 in. -A B FIND: a. The bending stress at A. b. The bending stress at B.

A 20-ft beam is subjected to the distributed load show. 0.75 in. -3 kip/ct A B K8 ft →→ 12 ft- UTION: D TOT 12 in. Beam Cross Section 0.75 in. -0.5 in. -A B FIND: a. The bending stress at A. b. The bending stress at B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m
Solid.mech.
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
QB4 BENDING STRESS The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure QB4). Determine: a) The position of the horizontal neutral axis. b) The second moment of area of the section about the horizontal neutral axis. c) The values of the maximum tensile stress and the maximum compressive stress in the beam if it supports a maximum bending moment of 1200x10 N.mm and the base face is in tension. 150mm 50mm 250mm +50mm I 50mm 150mm Fig QB4
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
SOVLE THE INTERNAL FORCE OF THE BEAM a) midspan of Lb)midspan f the left overhangc) midspan of the right overhand VALUES: P= 53 kN L= 8.1 m b= 1.8 m
8-46. The wide-flange beam is subjected to the loading shown. Determine the stress components at points A and B and show the results on a volume element at each of these points. 500 lb ↓ 2 ft 2 ft 2500 lb B 2 ft 4 ft 3000 lb 0.5 in.- Prob. 8-46 B 6 ft- 0.5 in. 1-4 in T 4 in. 12 in. 0.5 in.
3 The rigid bar EFG is supported by the truss system shown. Determine the cross- sectional area of member AE for which the normal stress in the member is 105 MPa. 0.90 SONRAWING D B R 15 kN -1.2 m 1.2 m-1.2 m-
The cross section of a steel beam is constructedof a W 18 × 71 wide-flange section with a 6 in. × 1/2 in.cover plate welded to the top flange and a C 10 × 30channel section welded to the bottom flange. This beamis subjected to a bending moment M having its vector atan angle θ to the z axis (see figure).Determine the orientation of the neutral axis andcalculate the maximum tensile stress σt and maximumcompressive stress σc in the beam. Assume thatθ = 30° and M = 75 kip-in. Note: The cross- sectionalproperties of this beam were computed in ExamplesD-2 and D-5.
A - determine force in member AB B - determine force in member AC C - Determine force in member AD
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. A C -1.2 m-1.2 m- D 1-1-1 B -1.2 m- b