Solve this problem and draw the graphs Problem 1: For the beams and loading shown,(a) draw the shear and bending moment diagrams. You must draw the graph by writing shear andmoment equations.(b) determine the maximum absolute values of the shear and bending moment.A6 kips 12 kips4.5 kipsCDEB2 ft2 ft2 ft2 ft(a)450 lbAC150 lb/ftDB4 ft8 ft+4 ft -→(b)

Answered: Problem 1: For the beams and loading…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy
Plot the shear and moment diagrams for the beam loaded with both the distributed load and the couple. Then answer the questions. I have solved for almost everything but I cannot figure out what my V&M Diagram should be.
For the problem shown below (left), W = 51 lbs while L1 = 4.4 inches and L2 = 12 inches. This results in the shear force diagram as shown on the right, where A, is the reaction force in the vertical direction at point A. Based on this shear diagram, what is the maximum moment in the portion of the horizontal beam from x = O to x = L1 in units of lb-in to two decimal places. (Be sure to use a negative sign to designate a negative moment if necessary.) A |--L1-——————— L2 Ay lb 0 -Ay lb W L1 L2 W -L1- BO L1- -X
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 4.0 kips/ft, a= 6.5 ft, and b= 17.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= tel tel a i B a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB B a PB Pc a C Pc C KN b KN D b D X D₂ X
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.8 m, b = 5.6 m, c = 3.8 m, P = 20 kN, w = 45 kN/m, and Q-10 kN. A P B W b C X What is the maximum bending moment on the beam? Answer in kN-m rounded-off to 2 decimal places When entering your answers, use the bending moment sign convention. I
Construct the shear and moment diagrams for the loaded beam shown. After you have the diagrams, answer the questions. 1.2 kN/m W A Questions: Atx 1.1 m, V = W = w₁+kx² 1.9 kN/m 4.5 m x KN, M= i kN·m At x = 3.7 m, V = i KN, M= The absolute value of the maximum shear Vmax force is The absolute value of the maximum bending moment is Mmax i II kN·m KN x = r KN-m, x = r
C and D pls
Please answer Part 3, thank you PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 6 m, b = 3 m, PB = 70 kN, Pc= 100 kN, and PE= 30 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax= 0, it has been omitted from the free-body diagram.) Answer: Ay = 50 kN Dy= 150 kN PART 2 Determine the shear force acting at each of the following locations: (a) x = 3m (b)x= 9 m (c)x = 13.5 m (d)x= 18 m When entering your answers, use the shear force sign convention. Answers: (a) V= 50 kN (b) V= -20 kN (c) V= -120 kN (d)V= 30 kN PART 3 (PLEASE ANSWER, THANK YOU) Determine the bending moment acting at each of the…
Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a-10.5 ft, b-24.0 ft, P- 20 kips and w - 5.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. B Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, - 0, it has been omitted from the free-body diagram.) Answers: kips Cy- kips Part 2 Determine the shear force acting at each of the following locations: (a) x = 10.5-ft (i.e., just to the left of point B) (b) x = 10.5+ ft (i.e., just to the right of point B) (c) x = 32.5 ft Note that x-0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.…
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 3.5 ft, b= 8.0 ft, t, c= 5.0 ft, d= 3.0 ft, w = 8.5 kips/ft and P = 54 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. P В D E b d For this loading, calculate the reaction forces A, and E, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A = 0, it has been omitted from the free-body diagram.) P B C E b d E, Answers: Ay = i kips, Ey = i kips.
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 19.5 kips/ft, a=6.0 ft, and b=21.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) Use your shear-force and bending-moment diagrams to determine the maximum positive bending moment, Mmax, pos, the maximum negative bending moment, Mmax, neg, and their respective locations, xmax, pos and xmax, neg. Use the bending-moment sign convention detailed in Section 7.2. The maximum negative bending moment is the negative moment with the largest…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS