For the problem shown below (left), W = 51 lbs while L1 = 4.4 inches and L2 = 12 inches. This results in the shear force diagram as shown on the right, where A, is the reaction force in the vertical direction at point A. Based on this shear diagram, what is the maximum moment in the portion of the horizontal beam from x = O to x = L1 in units of lb-in to two decimal places. (Be sure to use a negative sign to designate a negative moment if necessary.) A |--L1- Ay lb Ay lb W W · L2 ——L1- L2 B —L1-

Q: A a 90 B a G 30° b F b C

A: The values are

Q: A distributed load and a force is applied to a beam, where a = 2 m, b = 7 m, c= 3 m, w = 2 N/m, F =…

A: given data: a=2m, b=7m, c=3m, w=2N/m, F=5N and θ=450 AB=a=2m BC=b=7m CD=c=3m RV=vertical reaction…

Q: Part 3 Determine the bending moment acting at each of the following locations: (a)x-11.5-ft (i.e,…

A:

Q: Draw the free body diagram, shear force diagram, and bending moment diagram for section BC and AB of…

A: Drawing for section Bc,

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V…

A: a = 11 ftb = 4.5 ftc = 7.5 ftw = 4kips/ftM = 250 kip-ftTo find: shear force at the given locations

Q: c) the value of the maximum bending moment in the beam. Enter your answer in kNm to three decimal…

A:

Q: (c) Determine the 1st moment of area Q, of the top-half region A' (red shaded area) against z axis,…

A:

Q: The beam is supported at A and B as shown in (Figure 1). Suppose that F = 5 kip and w = 350 lb/ft.…

A:

Q: Determine the shear and moment as functions of position. (Round the final answers to four decimal…

A: This question is based on the concept of SFD and BMD

Q: Q-1 Draw the shear and moment diagram by area for the beam loaded shown in fig 5 KN 10 KN/m B C A 6m…

A: Shear force diagram represents shear force at every section of the beam.Shear force at any…

Q: The beam cross-section shown in the Figure Q6 is subjected to a resultant internal vertical shear…

A:

Q: A cantilevered beam is loaded with a uniformly distributed load as shown below. If w1 = 2000 lb/ft,…

A:

Q: The figure below shows the cross section of a beam, with each square measuring 10 mm x 10 mm. If the…

A: The side of each square, s = 10 mmThe internal shear force, V = 200 kN

Q: Draw the shear and bending moment diagram for the loaded bean shown below.

A:

Q: Q1. Figure below shows a simply supported beam that has a rectangular cross section 120 mm wide and…

A: Bending Moment Diagram of the beam:-

Q: Construct the shear and moment diagrams for the loaded beam shown. After you have the diagrams,…

A:

Q: 1. The axel loads for the truck shown below are P1 = 8 kips, P2 = 6 kips, P3 = 4 kips. Calculate the…

A: Let consider the point C,D,E are the the point where load P1, P2 ,& P3 acting respectively. P1=8…

Q: 400 Ib 400 lb 1.5 in. 200-lb/ft |6 in. B 3 in. 3 in. 1 in. 3 ft 6 ft 3 ft- a. Draw the shear and…

A:

Q: Pravinbhai

A: Step 1:Step 2:Step 3:Step 4:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.