Your company is using an automotive engine, having a single V-belt with φ= 18o and a unit weight of 0.25 Kg/m used to transmit 14kW of power from a 180mm diameter drive pulley rotating at 2000 rpm to a driving pulley rotating at 1500 rpm. The distance between the centres of the pulley is 300mm, if the coefficient of friction is 0.2 and the initial belt tension is sufficient to prevent slippage, determine the values of T1 and T

Your company is using an automotive engine, having a single V-belt with φ= 18o and a unit weight of 0.25 Kg/m used to transmit 14kW of power from a 180mm diameter drive pulley rotating at 2000 rpm to a driving pulley rotating at 1500 rpm. The distance between the centres of the pulley is 300mm, if the coefficient of friction is 0.2 and the initial belt tension is sufficient to prevent slippage, determine the values of T1 and T

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The belt drive in which pulleys rotate in the same direction is used to transfer power. The pulley diameters are 1.74m and 0.833m and it connects two parallel shafts which are 3.25m apart. The initial tension in the belt when it is stationary is 4500N. The smaller pulley is rotating at 710 rpm and coefficient of friction between the belt and pulley is 0.29. Determine the power transmitted by the belt drive
I need the answer as soon as possible
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
A leather belt of thickness 6 mm and width 80 mm connects two pulleys of 500 mm diameter and 900 mm diameter, their centres being 2.5 m apart. If speed of the larger pulley is 300 r.p.m, the coefficient of friction between belt and pulley is 0.25 and maximum belt stress is 100 N/cm2, determine the maximum power transmitted and initial belt tension.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt andpulley is 0.3, semi V-groove angle is 22.5o and angle of contact of belt with the pulley is 160o. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.Consider the centrifugal tension in the belt.
The Stroke of a gas engine which works on the constant volume cycle is 381 mm. The pressure at the beginning of the compression is 2.09 bar and at the end of compression is 13.05 bar. Assuming compression follows the law PV^1.36 = C, Calculate the clearance between the piston and cylinder cover at the end of compression in mm of length.
A body of weight 500N is prevented from sliding down a plane inclined at 20 to the horizontal by the application of a force of 50 N acting upwards and parallel to the plane. Find the coefficient of friction. If the body is to be pulled up the plane by a force acting at an angle of 30 to the horizontal, find the value of the force, and the efficiency of the lift. IMECHE
A 150lb man stands on a 60lb bar to which a cable is fixed at B. The cable passes over two fixed pegs with coefficients of friction indicated. Assume that the arrangement of the pegs permits the cable to contact each peg over a total angle of 90-degrees (90-degrees per peg). Assume that the normal force exerted by the man on the bar acts downward through A. Find the largest force the man can exert on the cable and maintain the bar horizontal.
estion 3 A flat belt drive connects two pulleys 5 meters apart. The 2m pulley diameter driver rotates at 350rpm, and the driven pulley has a diameter of 1.5m. The thickness and the mass of the belt drive is 5mm and 0.6kg respectively. The coefficient of friction between the belt and the pulley is 0.25. The belt experience 3% of slip during power transmission with a maximum tension of 1200N. Calculate the speed and torque of the driven shaft.
Two parallel shafts whose centre lines are 4 m apart, are connected by an open belt drive. The diameter of the larger pulley is 1.8 m and that of smaller pulley 3 m. The initial tension in the belt when stationary is 3 kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at 550 r.p.m. and length of the belt.
Find the power transmitted by a belt running over a pulley of 600 mm diameter at 200 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, angle of lap 160° and maximum tension in the belt is 2500 N.