Prepare the following LB media with antibiotic added. A 100ml of LB media with 25 micro/ml of Amp and 100micro/ml of Kan final concentration. A 100ml of LB is provided and amp of Kan stock at 100 mg/ml and 50 mg/ml are also provided. Find how much each antibiotic stock solution is needed to add 100ml of LB to reach desired antibiotic concentration.

Prepare the following LB media with antibiotic added. A 100ml of LB media with 25 micro/ml of Amp and 100micro/ml of Kan final concentration. A 100ml of LB is provided and amp of Kan stock at 100 mg/ml and 50 mg/ml are also provided. Find how much each antibiotic stock solution is needed to add 100ml of LB to reach desired antibiotic concentration.

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter10: Reconstitution Of Powdered Drugs

Section: Chapter Questions

Problem 8.1P

See similar textbooks

Similar questions

100ml of LB media with 25 μg/ml of Amp and 100 μg/ml of Kan final concentration. You have 100ml of LB provided and Amp and Kan stocks at 100 mg/ml and 50 mg/ml provided. Determine how much of each antibiotic stock solution you need to add to 100ml of LB to reach desired antibiotic concentration.
A vial of Doxorubicin reads 0•5g per vial. Instructions say to reconstitute each 12mg with 2•5ml of NS. How many ml of NS will be needed to reconstitute the vial of the recommended concentration? please show working
The SDS-PAGE protocol requires 0.5L of running buffer for the gel apparatus. The stock running buffer comes as a 20x concentrate. How should you prepare your running buffer? 50ml 20x stock + 450ml deionized water 450ml 20x stock + 50ml deionized water O 250ml 20x stock + 250ml deionized water 25ml 20x stock + 500ml deionized water 25ml 20x stock + 475ml deionized water 2ml 20x stock + 500ml deionized water O 100ml 20x stock + 400ml deionized water
How would you make two-fold serial dilutions such that the last tube is a 1:32 dilution of the original, concentrated material? Assume that you need to have at least 500 µl of each dilution, and you should be able to perform the dilutions in microfuge tubes with a maximum capacity of 1.5 ml.
1) You have been asked to make up four 1.5% agarose gels at 30 ml each. Ethidium Bromide is to be added at 0.5 ug/ml and you have a bottle at 10ug/ml. Write down step-by-step protocol of how to proceed. 2. How would you make up one liter of 1X TAE buffer using a 25X stock?
You have a sample at 50 ng/ul and you would like to load 400ng of this sample on a lane of an agarose gel. You also have TE buffer as diluent and 6x loading dye. Your total sample should be 12ul. Calculate the amounts of each reagent necessary to prepare this sample for gel loading.
Nutrient Agar (NA) is a general purpose medium used for the cultivation of a wide variety of non- fastidious microorganisms (Merck, 2000). Its ingredients are listed in Table 2. You are tasked to prepare 300ml of NA, determine the amount of ingredients and write in column 3 in Table 2. Show your calculations. *A sample calculation was made for you. Peptone = 300 ml x 0.5% = 1.5 g Table 2. Medium Composition of Nutrient Agar (NA) with the recommended proportions (Merck, 2019) Ingredients In % In Grams/300ml Peptone 0.5 *1.5 Meat extract 0.3 Agar 1.5 Distilled Water As needed
Following electrophoresis of the two pGlo mini-preparation samples (both digested and undigested), the following agarose gel image was obtained. provide an accurate and detailed figure, describing the image and what it depicts.
Discuss about the reagents used for agarose gel electrophoresis (not Polyacrylamide gel electrophoresis)
Calculate the volume of BSA stock that will be required to make the standard solutions needed to create the BSA standard curve. Be sure to show your work and include the volume of 0.02 M phosphate buffer required to reach a final volume of 1 mL. From a 2,000 μg/mL BSA stock, create 1 mL of each of the following stock solutions in 0.02 M phosphate buffer using individual microcentrifuge tubes: 50 μg/mL, 250 μg/mL, 500 μg/mL, 1,000 μg/mL, 1,250 μg/mL, 1,500 μg/mL. Be sure to properly label all the microcentrifuge tubes before creating the standards.
You have an order for 1 gram of Cefazolin in D5W 100 ml. You have added 5 ml of sterile water to the 1 gram vial to reconstitute powder. However the recommended manufacturer’s diluent amount is 10 ml of sterile water for a final concentration of 100 mg/ml. How would reconstituting the vial with 5 mls affect the concentration and the final calculated dose. Please answer with explanation ASAP. I will really upvote. Thanks
3) Define gel electrophoresis, including its theory and application. Describe the steps of running gel electrophoresis using the following image. More detailed reading: https://www.sciencedirect.com/topics/medicine-and-dentistry/agar-gel-electrophoresis POWER SUPPLY CATHODE ELECTROPHORETIC BUFFER ANODE WELL SAMPLE AGAROSE GEL POWER SUPPLY CATHODE ANOCE HIGH MOLECULAR WEIGHT SPECIES LOW MOLECULAR WEIGHT ANALYTES