Please write all theFormulas clearly for each case first,then solve the question by hand onpaper and send a clear photo of thesolution. Thanks a lotPower ElectronicsQ1) For the circuit shown in Fig (1).(a) Draw the output voltage and load current waveforms if the load is inductive. Explain theworking of each device.(b) If Vs 220V, load resistance is 10 2 and output voltage frequency is 50Hz.1. What is the rms value of the load voltage?2. Obtain Fourier series expression of the output voltage up to 7th order harmonic.3. Draw the frequency spectrum of the output voltage wave up to 7th order harmonic.T₁D₁DVoT₁D4Fig 1LoadT₂D

Answered: Image /qna-images/answer/c6baa736-4c0d-42a4-a504-b379ac9e0745.jpg

Answered: Please write all the Formulas clearly…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at the output is: O A. 73 W O B. 18 W C. None of the other choices are correct D. 36 W O E. 146 W
The input to a full-wave rectifier is 40 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is: O A. 27 V O B. 18 V O C. 36 V O D. None of the other choices are correct O E. 21 V
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
Please show all work, thank you!
A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V
Exe 1. A half-wave rectifier has a source of 120 V rms at 60 Hz and an R-L load with R=10 Ω and L= 10 mH.Determine, an expression for the load current, the average current, the power absorbed by the resistor, and the power factor. Hint: Beta=3.5 Rad
15)This multiple choice question from MEASUREMENTS INSTRUMENTATIONS course.
Construct a forward bias diode circuit in multi-sim (desktop, not live). Simulate and find the current through the resistor and the voltage across the resistor.
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 58 V and the firing angle of the SCR is 135 degrees, the RMS voltage at the output would be: O A. 98 V O B. None of the other choices are correct O C. 266 V O D. 399 V O E. 133 V
A single-phase controlled bridge rectifier is supplied from 120-V (rms) at 60-Hz utility. What is the rms voltage across the 24-Ohm load resistor if the delay angle is set to 121 degrees?
Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected transformer with ration 2:1. The load current has continuous character with negligible ripples and average thyristor current of 15A. The circuit inductance per phase is 1.2mH. The rectified voltage due to overlapping angle is 90 % of that voltage when this angle is neglected. 1- How much will the voltage drop be due to circuit inductance * 2- How much will the dc average voltage Vdc(alpha) be. 3- How much will the firing angle be ? 4- The overlapping angle. 5- How much is the percentage change of the output dc power if the thyristors T2, T4 and T6 are replaced by three diodes D2, D4, D6. 6- How much will be the maximum RMS phase current for the mentioned in previous task circuit ( semi-converter). 7- If an additional of 1 mH inductances are added to the existing inductances in the phases , how much will the overlapping angle be. The dc load current is kept constant & the…
(a) Figure Q2 (a) shows the image from the digital osciloscope. It shows two sine waveforms, voltage (Ch1) and current (Ch2). The value of vertical (volt/div) for Ch1, (amp/div) for Ch2, and horizontal scales (time/div) are shown in the image. Analyze the figure and determine: iv) Peak to peak value and the frequency for each waveform (voltage, Ch1 and current, Ch2) v) Phase different between two waveforms. vi) If the vertical scale (volt/div) of Chl is change to 100 V. Determine the total of division of Chl that will be displayed by the oscilloscope. Ch1 Ch2 Ch1 50V Ch2 5A M5.00ms Figure Q2 (a)

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS