D8.2. The field B = -2ax + 3ay + 4a, mT is present in free space. Find thevector force exerted on a straight wire carrying 12 A in the aAB direction, givenA(1, 1, 1) and: (a) B(2, 1, 1); (b) B(3, 5, 6).Ans. -48ay +36a, mN; 12ax - 216ay + 168az mN

if doubt arises please mention in the comments.

Answered: D8.2. The field B = -2ax + 3ay + 4a, mT…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

This is a part of a review I'm studying, NOT a graded assignment, please do not reject. I'm not getting the same answer as the given solution, may someone please explain their method on how to get the same solution?
A thin conducting wire is bent into the shape shown in the figure. The circular portion of the wire has radius 16.0 cm. The wire is in the plane of the screen and carries a current 3.50 A. What is the magnetic field at the center of the loop? (Give the magnitude in μT and select the direction from the options provided.) magnitude direction I -Select--- uT R 3
6- Why an insulator is represented as a capacitor C? What are the assumption modes?
Q8 - You wish to end up with a 2um width metal line (measured at the top of the metal lead cross section). A) You are using an isotropic wet etch process on a 1um thick metal layer. What linewidth should the protective photoresist line be to get these results? Sketch the resulting structure before photoresist strip. B) now you are using a completely anisotropic etch, what is the requisite linewidth of the photoresist to achieve the same end goal? Sketch the resulting structure before the stripping of the photoresist.
Please explain in detail. Thanks!
The Subject is Electromagnetic II .
Two long, cylindrical conductors of radii a, and a, are parallel and separated by a distance d, which is large compared with either radius. Show that the capacitance per unit length is given approximately by 1.7 C - TEo In- where a is the geometrical mean of the two radii. Approximately what gauge wire (state diameter in millimeters) would be nec- essary to make a two-wire transmission line with a capacitance of 1.2 x 10-11 F/m if the separation of the wires was 0.5 cm? 1.5 cm? 5.0 cm?
Determine the transition temperature and critical field at 4.2K for a given specimen of a superconductor if the critical fields are 1.41times10^(5) and 4.205times10^(5) amp/m at 14.1K and 12.9K respectively. how you conclude that the all superconductors are diamagnetic but all diamagnetic materials are not superconductors.
The figure below is a cross-sectional view of a coaxial cable. The center conductor is surrounded by a rubber layer, an outer conductor, and another rubber layer. In a particular application, the current in the inner conductor is I, = 1.16 A out of the page and the current in the outer conductor is I, = 2.90 A into the page. Assuming the distanced = 1.00 mm, answer the following. d (a) Determine the magnitude and direction of the magnetic field at point a. 2.32e-4 magnitude If you construct an imaginary circle of radius d passing through point a, how much current passes through this circle? UT direction ---Select--- (b) Determine the magnitude and direction of the magnetic field at point b. 1.16e-4 magnitude You can approach this problem by finding the field produced by current I, and the field produced by I, and then adding them vectorially. µT direction ---Select---
3. When you use complex notations for your field calculation, what is the physical consequence of a complex relative permittivity? Explain it in terms of field strength and phase.
This is a practice problem from the Engineering Electromagnetics course in my Electrical Engineering program. Could you please walk me through the steps of solving it so that I can solve more complicated ones in the future? Thank you for your assistance.
Given that the electric field E has a triangular profile as shown in the figure below, and that the built-in potential, Vo, is given by the total area under the triangle, find an expression for the maximum electric field magnitude, Emax, in terms of the dopant concentrations and fundamental constants. E Emax ^ Xn -Xp

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

D8.2. The field B = -2ax + 3ay + 4a, mT is present in free space. Find the vector force exerted on a straight wire carrying 12 A in the aAB direction, given A(1, 1, 1) and: (a) B(2, 1, 1); (b) B(3, 5, 6). Ans. -48ay +36a, mN; 12ax - 216ay + 168az mN