a) Three 30 2 resistors are arranged as shown in Figure 1 below. They are connected to a 480 V three-phase supply. The phase sequence is RYB anticlockwise. Calculate: i. The total power drawn by the circuit using the phase parameters. ii. The power read by each wattmeter. b) If Za, one of the 30 2 resistors, is now removed from the circuit, calculate: R- i. The line currents: IR, Iv, and la ii. The power read by each wattmeter. iii. The total power drawn by the two resistors. W₁ Be- W2 www 'R 22 12 B Figure 1

a) Three 30 2 resistors are arranged as shown in Figure 1 below. They are connected to a 480 V three-phase supply. The phase sequence is RYB anticlockwise. Calculate: i. The total power drawn by the circuit using the phase parameters. ii. The power read by each wattmeter. b) If Za, one of the 30 2 resistors, is now removed from the circuit, calculate: R- i. The line currents: IR, Iv, and la ii. The power read by each wattmeter. iii. The total power drawn by the two resistors. W₁ Be- W2 www 'R 22 12 B Figure 1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28P: For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be...

See similar textbooks

Similar questions

How to find % reduction in power.
Refer to Figure 8-31 to answer the following questions. Assume that a line voltage of 12,470volts is connected to the primary of the transformer and the line voltage of the secondary is 480volts. What is the turns ratio of the transformer? Assume the load has an impedance of 6Vper phase. What is the secondary line current? How much current is flowing in the secondary winding? How much current is flowing in the primary winding? What is the line current of the primary?
Please show your complete work in the solution
For the system shown in Figure 3.34. draw an impedance diagram in per unit by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators.
Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3 (b) 58 (c) 1
9. Three single phase transformers are used to transform 3 phase power. The primary winding of each transformer has 500 turns and the secondary has 75 turns. The primary windings are connected to a line voltage of 2.3kV. What is the secondary line voltage if the transformers are connected a) primary in wye secondary in delta? b) primary in delta and secondary in wye? c) open delta?
Voltage and current of a three – phase load are as follows: Voltage: 3.6 kV, 8 degrees Current: 37 A, 45 degrees What is the power factor of this load?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Choose the best
Can you solve the question step by step clearly ?
A star connected three phase alternator supplies power to a delta connected resistive load. The alternator has a line voltage of 480V. Each resistor of delta load has 8 ohm of resistance. Find the following values. Line voltage of the load (VL(load)) Phase voltage of the load (VP(load)) Phase current of the load (IP(load)) Line current delivered by the alternator (IL(alt)) Phase current of the alternator (IP(Alt)) Phase voltage of the alternator (VP(Alt)) True power
1. If two wattmeters are used to measure total power in a three-phase three-wire system does each meter measure single-phase power? Explain. 2. What is the significance of a negative indication on a wattmeter? 3. Would only one wattmeter be needed to measure the total three-phase power on a balanced three-phase four-wire system? Explain. 4. Must you see two wattmeters to measure the total three-phase power on a balanced three-phase three-wire system? Explain. 5. Can a wattmeter that has a current through its current coil and a potential across its voltage coil, indicate zero? Explain.