HW1: The location of the sliding bar in Figure below is given by x = 5t +2t³, and the separation of the two rails is 20 cm. Let B = 0.8x2a, T. Findthe voltmeter reading at (a) t = 0.4 s; (b) x = 0.6 m.

Answered: Image /qna-images/answer/8fc96885-ad2f-46f0-a413-259e769a4006.jpg

Answered: HW1: The location of the sliding bar in…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Electrical engineering
Please help me solve questions 1-5 using the given values found.
28.0 V [a]. Indicate on the figure and describe very R briefly where you are putting your junctions and loops. 4,00 A [b]. Find the current (I) through resistor R? + [c]). Find the resistance R? х6.00 Q [d].Find the unknown emf ɛ ? 6.00 A [e]. If the circuit is broken at point x, what is the current in resistor R? 3.00 N 3.
Find the potential difference between point a and point b for the situation shown below. Here ₁ = 12.0 V, E₂ = 7.77 V and R₁ = 4.33 №, R₂ = 6.44 , and R3 = 2.28 2. Va - Vb = R₂ E2 b R3 www R₁ &₁
In the figure, 8 = 138 V, R₁ = 10.702, R₂ = 29.402, R3 = 34.3 02, and L = 1.74 H. Immediately after switch S is closed, what are (a) i₁ and (b) i2? (Let currents in the indicated directions have positive values and currents in the opposite directions have negative values.) A long time later, what are (c) i₁ and (d) i2? The switch is then reopened. Just then, what are (e) i₁ and (f) i₂? A long time later, what are (g) i₁ and (h) i₂? (a) Number i (b) Number i (c) Number i (d) Number i (e) Number i Units Units Units Units Units R₁ R$ R₂ L
4.-For-labeled currents, draw an arrow to show the direction of the actual positive current. For labeled voltages, circle the node that is at the actual highest potential. Note that the positive and negative signs of the voltage represent the polarity of the probes of a voltmeter connected to the device. The value shown is the reading on the voltmeter. (segment of wire) 2A -2A -5A 2.de 3A TA Cov E 5V 12V + 3V -10V -201
I did a physics lab and got some values. I want to check them theoretically to see how the results differ. From this diagram, answer the following questions: The laws to be verified included the conservation of current in a node, the addition of potentials for components in series, and the addition of currents for components in parallel. The data : R1: 1094 ohm R2 : 998 ohm R3: 1094 ohmR4: 25 ohm Source 1 : 5 V Source 2 : 1.5 V
4. Consider the following circuit. 3R SR 2R a) How many distinct currents flow in this circuit? The four loops shown are labeled A - D, and the junctions are labeled a - d. b) If we had to solve for these currents, how many independent equations would we need? c) Which loops and/or junctions would you choose, if you had to solve for the currents? (Many answers are possible here.) This diagram shows several different loops and junctions in the circuit. d) Set up a system of equations that would allow you to solve for the currents.
Please answer in typing format please ASAP for the like Please answer in typing format please Please I will like it please thank
We now have a function file called myCircuit.m that solves for the currents in the following system of equations: i₁ + 12 = 13 V₁-i₁R₁ - 13R3 = 0 V2-i2R2 - 13R3 = 0 The circuit has R₁ = 1022, R₂ = 2002, and R3 = 409. The first battery has a fixed voltage V₁ = 35V, but the second battery can be adjusted to anything between 20V and 60V. We want the current is to be 0.77A. We will find the V₂ that produces this current by starting at V₂ = 20V and incrementing V₂ by 0.01V until we get i3 greater than or equal to 0.77A. Write a script file called current.m that calls myCircuit.m inside a while loop in order to determine what voltage we should select for V₂. This problem assesses how you can handle vector outputs to functions.
Two batteries, A and B, are connected in parallel and an 80 ohm resistor is connected across thebattery terminals. The e.m.f. and the internal resistance of battery A are l00V and 5 ohm respectively,and the corresponding values for battery B are 95V and 3 ohm respectively. Find (a) the value anddirection of the current in each battery and (b) the terminal voltage
I need answers with clear hand writing or using Microsoft word . ASAP measurements , describe how to read the values given on the measurement tools and to write about measurement tools note: i want a lot of information

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

HW1: The location of the sliding bar in Figure below is given by x = 5t + 2t³, and the separation of the two rails is 20 cm. Let B = 0.8x2a, T. Find the voltmeter reading at (a) t = 0.4 s; (b) x = 0.6 m.