Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 12 mm and an allowable normal stress of 80 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 7 mm, and an allowable normal stress of 80 MPa. Assume x₁ = 3.7 m, x2 = 1.2 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. y (1) (2) P

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 12 mm and an allowable normal stress of 80 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 7 mm, and an allowable normal stress of 80 MPa. Assume x₁ = 3.7 m, x2 = 1.2 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. y (1) (2) P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7…

A: Diameter of tie rod (1) = 7 mmDiameter of pin B = 5 mmLengths:a = 670 mmb = 335 mmh = 370 mmAngle=to…

Q: The solid circular rod has a cross-sectional area of 310 mm2. It is subjected to a uniform axial…

Q: The mechanical system consists of two identical steel rods (A = 30 mm', E= 20OGPA, a = 15x10/°C) and…

A: Given: The area of rods, A = 30 mm2 The Modulus of elasticity, E = 200 GPa The Thermal coefficient…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Given data as per question compressive load of P = 55 kips α= 30°. calculating the inclined plane…

Q: roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Givenallowable stress of rod σa=86.60MPaallowable shear stress on pin A=60MPadouble shear stress

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3100 mm² and an…

A: According to the given dataThe area of bar 1 is .The allowable normal stress in bar 1 is .The area…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 2850 mm2 and an…

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given data: p=5 MPar=500 mmt=10 mm Need to determine the average circumferential (hoop) stress.

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

Q: PROBLEM 1 A threaded steel rod (E=210 GPa, d: = 15mm, linear coefficient of expansion= 12x10-6/0C)…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3200 mm² and an…

A: To Find : The maximum load Pmax. Given : The cross section area of bar 1 is A1=3200 mm2 The cross…

Q: Neglecting the weight of the bar as shown in the figure, determine the stress in each rod if the…

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

Q: mm. When subject to pressure, the hoop stress in

Q: 800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular…

A: Stress due to eccentric axial load of 800N P1=P2=800N P2 and 800N will create a moment M=800(0.8)=64…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: According to the given dataBarNormal-StressDiameterThickness1175MPa10mmNA216548mm6Considering the…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: 2. Two elastic bars are connected and supported as shown. The thermal load is a 10°C temperature…

Q: A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

Q: Answer: Pmax= i kN

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load P at…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

A: The free-body diagram of the given system is,From the given diagram, = tan-1 (h/a) = tan-1 (470/580)…

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: A thin cylinder of inner radius 500 mm and thickness 10 mm subjected to an internal pressure of 5…

A: Given Data⇒ Internal Pressure(P)=5 MPa Inner radius(R)=500 mm Thickness(t)= 10 mm

Q: The lap joint shown is fastened by four 4-in.-diameter rivets. Calculate the maximum safe load P…

Q: The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 47 kN. Assume that a = 300 mm,…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9…

A: According to the given data Diameter of the BD member =D=9 mm Pin at B is in double shear with…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 12
mm and an allowable normal stress of 80 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 7 mm, and an allowable
normal stress of 80 MPa. Assume x₁ = 3.7 m, x₂ = 1.2 m, and y₁ = 4.0 m. Determine the maximum load Pmax that can be supported by the
structure without exceeding either allowable normal stress.
9₁
(1)
Answer: Pmax=
B
(2)
3°
P
C
kN
2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data and what is to be determined-

VIEW

Step 2: Calculate force in tie rod and force in pipe in terms of applied force P-

VIEW

Step 3: Calculate maximum load supported by the structure-

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rectangular bar is connected to the support bracket with a 25-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax i kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= (1) i B b C /9 KN h P
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4250 mm2 and an allowable normal stress of 95 MPa. Bar (2) has a cross-sectional area of A2 = 2750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.1 m, x2 = 3.6 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN
Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm², E = 200GPA, a = 15x106/°C) and a "rigid" beam AC. The beam is supported by a smooth pin at B. The nuts at A and C are initially tightened just enough to remove the slack, leaving the two rods stress-free. 1- Determine the axial stresses induced in rods (1) and (2) if the temperature of both rods is decreased by 60°C. 2- Determine the (small) angle 0 through which the beam AC would rotate due to this temperature change. -200 mm- - 80 mm- A 0f B "Rigid" |(1) (2) 250 mm
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3950 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 2.0 m, x2 = 3.0 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 330 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= i B kN h
Find the stresses in each section and total change in length of the bar as shown in figure. The bar is subjected to an axial pull of 24 kN. Take the diameter of section 1 as 56 mm, length L1 as 44 mm, ,the dimensions of section 2 as 65 mm x 63 mm, L2 as 16 mm, section 3 is a square of size 30 mm, length L3 as 50 mm. Also take the Young’s modulus of sections as E1 = 2.1x105 N/mm2, E2 = 1.1x105 N/mm2, E3 = 0.75x105 N/mm2 (i) Stress in section 1 (unit in N/mm2) is = Answer for part 1 (ii) Stress in section 2 (unit in N/mm2) is = Answer for part 2 (iii) Stress in section 3 (unit in N/mm2) is = Answer for part 3 (iv) Total Change in length of the given bar (unit in mm) is =