A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stres , perpendicular to plane AB and the shear stress T parallel to plane AB. Assume a = 30°. P A В Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.

Q: The distributed load is supported by a box beam as shown below. Determine the maximum value of wo…

A:

Q: The solid circular rod has a cross-sectional area of 310 mm2. It is subjected to a uniform axial…

A:

Q: 1 Awall bracket, as shown in Fig, is subjected to a force P = 5 kN, The cross-section of bracket is…

A:

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: A compression load of P = 55 kips is applied to a 3 in. by 3 in. square post, as shown. Determine…

A:

Q: ess of bar: 6 m mm mm adius, r= 4 mm

A:

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

A:

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: stress is defined as the force per unit area.

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: For the stresses given with the cube below: 1. Compute the center, radius (R), principal normal…

A:

Q: roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Givenallowable stress of rod σa=86.60MPaallowable shear stress on pin A=60MPadouble shear stress

Q: The principal stresses at a point in an elastic component are 61 62 63. For given values of 02 and…

A:

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: 228 kN B 2.5 m C -4.0 m- 4.0 m- Shown in the figure above is a truss (E = 300GPA) with 228KN…

A:

Q: Two ropes are used to hoist a 610 Ib engine/transmission assembly as shown. The rope is anchored at…

A: Since we only answer up to 3 sub parts. We will answer first 3. Please resubmit the question and…

Q: A carbon steel ball with 27-mm diameter is pressed together with an aluminum ba Determine the…

A: Carbon Diameter, dc = 27 mmAluminium Diameter, dA = 35 mmForce, F =11 NPoissons Ratio, 0.3…

Q: The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports…

A: Given:

Q: For the shown figure, determine the average normal stress (MPa) developed in rod BC if the load has…

A:

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

A: GivenP=58kNw=14 kN/mL=3mAy=45.67 kNDy=54.33 kN

Q: Draw and stress tensonr with the following characteristics The stress cube visualization at point…

A:

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: For the figure shown determine the value of the maximum normal stresses, due to the change of…

A: given; lets take reaction force at E=R1lets take reaction force at F=R2

Q: Calculate the force which can be applied in the punch shown in the figure if the allowable shear…

A:

Q: 10 KN 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m D 5 KN / m F 50 KN-m E 3. Points C and D of…

A: Given DataP=10kNw1=5kN/mw2=20kN/m

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: To read quetsion carefully

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: Given data: F1=120 kNF2=90 kN Need to determine the absolute value of the deformation at point C.

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A:

Q: DETERMINE STRESS (MPa) OF MEMBER EG in the truss shown. Input your answer in two (2) decimal places…

A:

Q: Link AB, of width b= 2 in. and thickness t = in., is used to support the end of a horizontal beam.…

A:

Q: Problem: Figure shows a frame subjected to a load of 3.4 kN, find the resultant stress at A and B.

A:

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: A link is loaded as shown, it is attached with two bolts with a diameter of and its thickness is 0.1…

A: The diameter of bolt is The width of link is The thickness of link is The normal stress on link is

Q: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB

A: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB.

Q: is apple showr on member ABC that is held by the 15-mm diameter cable. The pin at the support C is…

A:

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

A:

Q: The lap joint is fastened with four ¾-inch diameter rivets.  a. If the allowable shearing stress of…

A:

Q: 800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular…

A: Stress due to eccentric axial load of 800N P1=P2=800N P2 and 800N will create a moment M=800(0.8)=64…

Q: 1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa,…

A: GivenP=15000NLi=40mmLo=L=?σallow=75MPa=75 N/mm2

Q: A compression load of P = 50 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.