The rectangular bar is connected to thesupport bracket with a 25-mm-diameter pin.The bar width is w = 65 mm and the barthickness is 10 mm. Each side of the brackethas the same dimensions as the bar. Theaverage shear stress in the pin cannot exceed115 MPa, the bearing stress in the barcannot exceed 120 MPa, and the bearingstress in the bracket cannot exceed 140 MPa.Determine the maximum value of Pmax thatcan be supported by the structure.Answer: PmaxikN

Answered: Image /qna-images/answer/d647ee36-4644-43c9-a884-9e25329c66f2.jpg

Answered: Answer: Pmax i kN

Engineering

Mechanical Engineering

Answer: Pmax i kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is w = 65 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 125 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax= P Mi KN
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 80 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 125 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. P KN Answer: Pmax= i
The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is w=60 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax KN
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w = 60 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 120 MPa, and the bearing stress in the bracket cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported by the structure.
Please answer question number 4.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. 20 mm
An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20 mm 20 mm 5 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 250 mm Determine the normal stress in the brass shell. The normal stress in the brass shell is MPа.
The structure shown below is made of 3 circular rods, each with a diameter of 1.0" and lengths as shown in the diagram. Rod AB is aluminum (E = 10E6 psi) and rod BC is steel (E = 30E6 psi) and rod CD is brass (E = 15E6 psi). The structure is axially loaded as shown in the diagram. Determine the maximum stress and its location and the change in length of the structure due to the applied loads. You may ignore the flanges that connect the rods (considered rigid). A 4 ft B 900 lb 6 ft 300 lb 2 ft C D
Question 4: Two wrenches are used to tighten the pipe. If the pipe is made from a material having an allowable shear stress of Tallow = 85 MPa, check the allowable force for external and internal diameter of pipe and determine the allowable maximum force P that can be applied to each wrench. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm. 250 mm B 250 mm Figure 4 Answer: Torque = 0.5P, Polar moment of inertial J = 2.26 x 108 m4, outer diameter PS %3D 307.36N, inner diameter P S 384.2 N, Pallowable = 307.36N
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 165 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 8 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 3.8 m, x2 = 1.6 m, and y₁ = 4.2 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. 3₁ Answer: Pmax (1) B P kN