4. The three steel (E= 29 x 10 psi) eye-bars, each 4 in. by 1.0 in in cross section, are assembled by driving 7/8-in.-diameter drift pins through holes drilled in the ends of the bars. The distance between the holes is 30 ft in the two outer bars, but 0.045 in less in the middle bar. Find the shear stress developed in the drift pins. Neglect local deformation at the holes. 1.0 in. 30 ft in. 4 in.

4. The three steel (E= 29 x 10 psi) eye-bars, each 4 in. by 1.0 in in cross section, are assembled by driving 7/8-in.-diameter drift pins through holes drilled in the ends of the bars. The distance between the holes is 30 ft in the two outer bars, but 0.045 in less in the middle bar. Find the shear stress developed in the drift pins. Neglect local deformation at the holes. 1.0 in. 30 ft in. 4 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 20 please, Show graph : )
I need parts 3 and 4 answered pertaining to the print provided. I asked this question previously on here and I received the wrong answers to the 2 parts Im asking about, so I am reposting the question again to have another tutor answer it. Part 3: I need to tell what was ommited. Part 4: I need to tell what the triangle equals? Lower right or J1 zone has the answer.
Question 1 Figure Qta shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force Fi acts vertically with a force of 2170 N; and F2 acts at an angle e relative to the y-axis with a force of 1240 N. F1 F2 Figure Qta Cable Anchor Point a) For Figure Q1a, at what angle @ must the force F2 ( 1240 N) be applied in order that the resultant force R of the two forces Fi and F2 has a magnitude of 3100 N? Give your answer in degrees to 2 decimal places. b) For Figure Q1a, what is the angle between the resultant force R (3100 N) and the yaxis. Give your answer in degrees to 2 decimal places. c) The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force Fanecessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceilling anchor points A and B. Assume frictionless and weightless pulleys and useg-9.81 m/s'.
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
I need help matching the following terms to the phrase it describes. Answers are used only once.
20 lbf 200 kg D 250N 20 kN m A 2 FT 200 kg
Please solve all three.
Isn't the area of the circle equal to pi times the square of its radius?
To convert an arc to a circle: a. Use the FILLET command with a 0 radius b. Use the EXTEND command c. Use the LENGTHEN command d. Use the JOIN command
D Question 19 Find the area of the figure shown. a=3 cm b= 6 cm Take pie=3.14 Round answer to one decimal place. just write the number without units a
Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm 1 cm A B 0.5 cm 6 cm -Xc 0.75 cm E 0.75 cm 0.75 cm- e 0.5 cm 2 cm F.
Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L L 2L 3 L -- L Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result as m without writing units.) Response: Question 3-B) Find the Y coordinate of the geometric center of the plate . (Enter your result as m without writing units.) Response: