Part AMomber CB has a square cross section of30 mm on each side. (Figure 1)Determine the largest intensity u of the uniform loading that can be appled to the frame without causing eitherthe average nomal stress or the average shear stress at section b-b to exceed o= 19 MPa andT= 20 MPa, respectively.Express your answer to three significant figures and include appropriate units.ValueUnitsSubmitRequest AnswerProvide FeedbackNext >Figure1 of 1

Answered: Image /qna-images/answer/a5109f4d-cd23-4e0c-96cc-ade063e102d6.jpg

Part A Member CB has a square cross section of 30 mm on each side. (Eigure.1) Determine the largest intensity u of the uniform loading that can be applied to the frame without causing either the average normal stross or the average shear stress at section b-b to exceed a 19 MPa and T= 20 MPa, respectively. Express your answer to three significant figures and include appropriate units. ? Value Units Submit Bequest Answer Provide Feedback Next > Figure 1 of 1

Part A Member CB has a square cross section of 30 mm on each side. (Eigure.1) Determine the largest intensity u of the uniform loading that can be applied to the frame without causing either the average normal stross or the average shear stress at section b-b to exceed a 19 MPa and T= 20 MPa, respectively. Express your answer to three significant figures and include appropriate units. ? Value Units Submit Bequest Answer Provide Feedback Next > Figure 1 of 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam is made from four plates and subjected to a shear force of V-26 kN (Figure 1) Figure 0 25 mm 10 3 50 mm 25 mm 50 mm 150 mm 150 mm 50 mm 4 1 of 1 D Part A Determine the maximum shear stress developed in the beam at point A Express your answer to three significant figures and include the appropriate units. Submit Provide Feedback Value Request Answer Units
A shear force of V = 240 kN is applied to the box girder. (Figure 1) Figure Part A 9A= 28.82 Part B 200 mm B 90 mm μÅ LO 9B = 16.42 200 mm 10 mm. A μÅ C D 180 mm Determine the shear flow at point A. Express your answer to three significant figures and include the appropriate units. MPa 90 mm Submit Previous Answers Request Answer 100 mm 190 mm -10 mm X Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units. MPa Determine the shear flow at point B. Express your answer to three significant figures and include the appropriate units. ? Pocke Submit Previous Answers Request Answer 1 of 1 ? > Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units.
MENG222 STRENGTH OF MATERIALS P=1000
question: a)Calculate the axial elongation of the member b)Calculate the new cross section area after the elongation ,considering the Poisson ration effect c)If the material has an ultimate shear strength of 12Mpa and applying a factor of safety of 1.5,what is the maximum tensile load this member could take without failing in shear.Calculate the failure plan inclination theta
QUESTION 4 The following figure represents a cross section through a long opening. The magnitudes of the plane components of the field stresses are o,= 13.75 MPa, o, = 19.25 MPa, Ty = 4.76 MPa, expressed relative to the reference axes !! shown. 1. Calculate the maximum and minimum boundary stresses in the excavation perimeter, defining the locations of the relevant points. 2. If the strength of the rock mass is defined by a maximum shear strength criterlon, and the shear strength is 20 MPa, estimate the extent of boundary failure, in terms of the angular range over the perimeter.
The frame in (Figure 1) supports a centrally applied distributed load of 1.8 kip/ft. The pins at C and D are at the same location as the neutral axis for the cross section. Figure 12 ft C A 5 ft- HH 3 in. 3 in. 1 in. B 1.5 in. 6 in. 16 ft 1.8 kip/ft D 1 of 1 > Part A Determine the state of stress at point A on member CD. Enter your answers in kilopounds per square inch to three significant figures separated by a comma. Enter negative value for the normal stress in the case of compression and positive value in the case of tension. A. TA 10.744,0 Submit Part B VAΣ 1 vec X Incorrect; Try Again; 5 attempts remaining OB. TB = Previous Answers Request Answer Submit Determine the state of stress at point B on member CD. Enter your answers in kilopounds per square inch to three significant figures separated by a comma. Enter negative value for the normal stress in the case of compression and positive value in the case of tension. VAΣo↓vec - 23.236,0 Previous Answers Request Answer X Incorrect;…
Ineed answer within 20 minutes please please with my best wishes
please do it fast and clearly and don't copy from others otherwise skip please thanks
nt 2 poa page 25 ol 40) - Google Orome nline.gmitie mod/quz/attempt.phplattempt-514100omid-4251718pages24 GMIT 25 A strel -200 Ga rod with a circular cross section k long Determine the minimum diameter reguired if the rod must transmit a tensile force of 50N withut eceeding an alowable stress of 180 M State your answer in mm without including the units and correct to two decimali places Answer ous page Nt pg 9ype here e ah
Please solve all part
The bar is made from steel and has an allowable stress of allow = 19.7 ksi (Figure 1) Figure P 1.875 in. 0.75 in. -0.125 in. 1.25 in. r 0.25 in. 1 of 1 Part A Determine the maximum axial force P that can be applied to the bar. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?
i need the answer quickly