QUESTION 4The following figure represents a cross section through a long opening. The magnitudes of the plane componentsof the field stresses are o,= 13.75 MPa, o, = 19.25 MPa, Ty = 4.76 MPa, expressed relative to the reference axes!!shown.1. Calculate the maximum and minimum boundary stresses in the excavation perimeter, defining the locationsof the relevant points.2. If the strength of the rock mass is defined by a maximum shear strength criterlon, and the shear strength is20 MPa, estimate the extent of boundary failure, in terms of the angular range over the perimeter.

Answered: Image /qna-images/answer/e211124b-b8ee-4cd5-bd59-c353b5d15d6b.jpg

QUESTION 4 The following figure represents a cross section through a long opening. The magnitudes of the plane c of the field stresses are o, = 13.75 MPa, o, = 19.25 MPa, Ty = 4.76 MPa, expressed relative to the ret shown.

QUESTION 4 The following figure represents a cross section through a long opening. The magnitudes of the plane c of the field stresses are o, = 13.75 MPa, o, = 19.25 MPa, Ty = 4.76 MPa, expressed relative to the ret shown.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. y 40 Mpa
The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 20 MPa, S, = 24 MPa, and Sy = 29 MPa. Assume ß = tan = 21.8°, a = 5, and b = 2. Using the equilibrium equation approach, determine the normal and shear stresses o (positive if tensile, negative if compressive) and z (magnitude only) at this point on the inclined plane shown. Answers: i MPa, T = i MPа.
The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L = 470 mm, H = 395 mm, d₁ = 2 mm, d₂ = 4 mm, d3 = 14 mm, d4 = 9 mm, 2 mm, and do 4 mm d5 Figure H L B dz d 1 of 1 Part A Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. (YC)zy = Submit Part B μA (YD)zy = Value Request Answer Determine the shear strain Yzy at corner D. Express your answer to three significant figures and include appropriate units. μA Value Units Submit Request Answer ? Units ?
The state of plane stress at a point is presented by the stress element shown in figure 2. find the stresses acting on an element oriented at 30° Clockwise. With respect to the orignal element.also draw neat and to the scale Mohr's circle of the given problem. Take X=4740
There is a rectangular plate 2 mm thick on which the forces shown in the figure act. Determine Mohr's circle and derive the values and directions of the principal stresses (σmax , σmin , 2 theta subscript P) at point P on the plate. Results in MPa and degrees.
Determine the total stress at point A on the cross section a-a in the figure below. 400 kN a -0.5 m- 300 mm 100 mm 100 mm Section a-a
Find the interal normal stress in all relevant segments of the bar in the picture.
The stresses shown in Figure below and act at a point on the free surface of a machine component. Determine the normal stresses σ x and σ y and the shear stress τ xy at the point.
A 45° strain rosette (see figure) mounted onthe surface of an automobile frame gives the followingreadings: gage A, 310 X10-6 ; gage B, 180 X10-6 ;and gage C, -160X10 -6 .Determine the principal strains and maximumshear strains, and show them on sketches of properlyoriented elements.
An element in biaxial stress is subjected tostresses σx = -29 MPa and σy = 57 MPa, as shownin the figure. Using Mohr’s circle, determine thefollowing.(a) The stresses acting on an element oriented at aslope of 1 on 2.5 (see figure).(b) The maximum shear stresses and associated normalstresses.Show all results on sketches of properly orientedelements.
In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 597 587 567 O O O
1.5 kN 120 mm Outer diameter: 72 mm Inner diameter: 62 mm 150 mm D 120 mm 4.5 kN A For element A find: (a) Torsional shearing stress (b) Transverse shear stress (c) Normal stress Q = [AS] × y 2rm TU y =