µA ? The cooling unit has a total weight of 50 kip and a center of gravity at G. (Figure 1) Value kip Nc = Submit Previous Answers Request Answer X Incorrect; Try Again; 9 attempts remaining Check your signs. Figure < 1 of 1 > Part B Determine the resultant shear force on the cross section at point C. Express your answer to three significant figures and include appropriate units. Vc = 0 kip Submit Previous Answers 0.2 A1 ft 3ft v Correct

Q: In sand casting process, the pattern is made of

A: Casting is a process in which liquid metal is poured into the mould of a casting and the desired…

Q: 1- The effective porosity is the value that is used in a gas reservoir engineering calculations.

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: Figure 6(a) shows an example of pressure vessel with radius ofr, and yield stress O. Suppose the…

A: Calculated the minimum thickness to sustain the pressure vessel according to the von mises yield…

Q: Briefly describe the principle of corresponding states:

A: When the characteristics of actual gases at their critical states are known, the law of comparable…

Q: the parts of a micture can be         using the physical properties of the compund

A: Compounds are substances made up of two or more elements whereas mixtures are made up of elements or…

Q: Q\Why the metals family could be strengthening

A: Both crystalline and amorphous materials may have their yield strength, ductility, and toughness…

Q: the effect of scratching the of the iron sheet surface with different objects

A: Effect of scratching the of the iron sheet surface with different objects.

Q: Instruction: Explain briefly the difference between Annealing and NOrmalizing

A:

Q: 9. What is the CNA? (I don't know what it means, but something related to engineering, what would…

A: There are many acronyms for CNA . But as you mentioned it is related to engineering field it stands…

Q: Describe Scavenging

A: IC engine completes one power stroke in four strokes. Intake of A/F mixture Compression Power…

Q: Instruction: : Explain briefly the hardening pr0cess Of a metal.

A: given; explain briefly the hardening process of a metal.

Q: Why is it important to resist the loadings?

A: Loading is defined as an external force or a couple to which a member is subjected during its…

Q: discuss the process of creating a good finish when using metals as a raw material in making a…

A: we are to discuss what are methods of generating a better finish with metals

Q: Problem 5 point loading. Its elastic modulus E' is 100 GPa. Its both ends are pin connections: K of…

A: Problem 5 (20 pts) The shaft is subject to a compressive force without the torque and the point…

Q: How does the element of material deforms?

A: elements of a material are deformed when some external force is applied to it.

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: what is p3?

A: the pressure at state 1 and 2, P1 = 10 bar the temperature at state 1, T1 = 400 C The temperature at…

Q: how do the engine cylinders are made , make a flow chart and mention the process and types of…

A: Engine cylinders are made using casting process, where molten liquid metal will be allowed to…

Q: what are the parts of a plumb bob

A: A plumb bob is an Instrument ,Which is used in construction and other fields to determine vertical…

Q: What is Hazard and why it is important?

A:

Q: What were the construction materials used on Gariep dam.

A: Given data→Gariep damProblem statement ⇒Problem says name the materials used in gariep dam.

Q: Name at least two fluids you can see on your household and provide photos for each.

A: Fluid- when any gas , liquid or any material which has ability to flow under application of any…

Q: What is the other name for the short column?

A:

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: You are required to describe thoroughly how the two parts can be fabricated in the workshop so that…

A: The processes involved in making the lamp holder are: Milling Drilling Internal thread cutting…

Q: Derive a mathematical equation to estimate the clamping force of a center gate disc molding.

A: The clamping force needed for a gates disc mould needs to be evaluated.

Q: Q16. A mug is to be made from alumina. Which forming method would be most suitable?

A:

Q: where did you guys get the area from?

A:

Q: Identify the mold die material in order to produce the steel casting parts.  Wood Cast iron Steel…

A: Given :-  Identify the mold die material in order to produce the steel casting parts.  Wood…

Q: Draw TWO (2) casting process that would be most suitable for making a good and jewellery.

A: 1: Investment casting also know as lost was casting is used for making jewellery.

Q: ist five important criteria in predesign analysis for the  whole process fabricating the jigs and…

A: Jigs and fixtures: Jig and fixtures are the production tools used to accurately manufacture parts.…

Q: Write in detailed  steps to select the right material for  cooking ware

A: Steps to select the right material for cooking Ware

Q: Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.