P3 In general, the load resistance is given and the resistors of the voltage divider must be matched to the load. What should be considered when designing the resistors? The load current should be roughly 10 times higher than the supply current The load current should be roughly 10 times lower than the supply current The load resistance must be much higher, approximately at least 10 times higher than the parallel connected resistor of the voltage divider. The load resistance must be much lower, approximately at least 10 times lower than the parallel connected resistor of the voltage divider. ☐

P3 In general, the load resistance is given and the resistors of the voltage divider must be matched to the load. What should be considered when designing the resistors? The load current should be roughly 10 times higher than the supply current The load current should be roughly 10 times lower than the supply current The load resistance must be much higher, approximately at least 10 times higher than the parallel connected resistor of the voltage divider. The load resistance must be much lower, approximately at least 10 times lower than the parallel connected resistor of the voltage divider. ☐

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Now, double the value of R1 and R2. Disconnect the load and make sure that VNL (No Load) is the same as the original circuit. Then repeat the VOUT measurements for load values of 50 Ohm and 500 Ohm. Was the loaded voltage divider more stable or less stable than the original circuit? (In the book it provides the current values but in the problem it provides no current ranges) This relates to voltage divider stability. I think its asking me to compare the stability of the No Load circuit with the Resistor Load circuit.
A voltage divider consists of a 3000 – ohm, a 5000 – ohm, and 10000 – ohm resistor in series and the series current is 15 mA. Find (a) the voltage drop across each resistance and (b) the total voltage.
Please explain correctly in detail. I will upvote. Thank you.
Use multism
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
The circuit below is used as a voltage divider. The input voltage is 12 V. The output voltage (that is the voltage across R2) must be 9.1 V. The current consumed by the divider must be 3.5 mA. Find the required resistances R1 and R2. (Unit:Ohm) R1 R2 R1 = R2 =
Employing the characteristic curve in Figure 1 and obtain the design for a voltage divider configuration that has a Q point of ICQ = 5 mA and VCEQ = 8 V. Using VCC = 24 V and RC = 3RE. Find the following: a) Draw the configuration indicating each of the elements b) Determine RC and RE c) Find VE d) Determine VB e) Calculate ? for point Q f) Find R2 if R1 = 24 kΩ
With the figure below and utilizing the given (assumed) direction of current in junction A. Find the individual current and voltages of each resistors. Given: Rị = 1 N VA = 3 V R2 = 2 N VB = 6 V R3 = 3 N Vc = 9 V R4 = 4 N R, IL Va, Rz A I3 Rot B VB
Kindly answer all of the questions please, I will rate you with like/upvote. Please answer all of the questions. Thank you so much.
True False 0000000 ☐ ☐ ☐ ☐ ☐ ☐ ☐ Are the following statements about unloaded voltage dividers true or false? A voltage divider is a series connection of resistors. A voltage divider is a parallel connection of resistors. In a voltage divider, the currents through the resistors are equal. In a voltage divider, the currents through the resistors behave like the ratio of the resistors. In a voltage divider, the currents through the resistors behave like the ratio of the reciprocal values of the resistors. In a voltage divider, the voltages across the resistors are equal. In a voltage divider, the voltages across the resistors behave like the ratio of the resistors. In a voltage divider, the voltages across the resistors behave like the ratio of the reciprocal values of the resistors. П ☐
Two resistors connected in parallel have values of R, - 20 Ohms and R, - 40 Ohms. supply is 10 A. of current through each resistor. 6. The total current coming from the voltage Use the current divider rule to find the value I=10A R200 R = 400 %3D
Two 3.3 k2 resistors are in series combination are in parallel with a 4.7 k2 resistor. What will be the voltage across the 4.7 k2 resistors if the voltage across one of the 3.3 k2 resistors is 12 V Select one: O a. 12 V b. 6 V O c. 24 V O d. 0 V