Two 1kN resistors are connected in series from point A to point B; their junction is labelled C. Two more resistors are connected in series from A to B; their junction is labelled D. A to D is a 1 kN resistor while D to B is an unknown resistor R. A galvanometer is then connected between C and D, and a battery is connected across A and B. Finally, a potentiometer consisting of a 20 cm length of high-resistance wire, 25 kNm-1, with a sliding contact is connected, the bottom of the wire to B and the slider to D, in parallel to R. When the slider is 8 cm from the bottom, the galvanometer reads zero. i) Draw the circuit diagram. ii) Calculate the value of the unknown resistor R.

Two 1kN resistors are connected in series from point A to point B; their junction is labelled C. Two more resistors are connected in series from A to B; their junction is labelled D. A to D is a 1 kN resistor while D to B is an unknown resistor R. A galvanometer is then connected between C and D, and a battery is connected across A and B. Finally, a potentiometer consisting of a 20 cm length of high-resistance wire, 25 kNm-1, with a sliding contact is connected, the bottom of the wire to B and the slider to D, in parallel to R. When the slider is 8 cm from the bottom, the galvanometer reads zero. i) Draw the circuit diagram. ii) Calculate the value of the unknown resistor R.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 6RQ: True or False: A bimetal is a combination of two pieces of metal that are welded together, each with...

See similar textbooks

Similar questions

Three resistance 14. 5 Q, 25. 5 Q and 60 Q are connected in series across 200 V. What will be the voltage drop across 14. 5 Q (a) 29 V (b) 13. 5 V (c) 14 V (d) 18 V
Determine the resistor voltage. The source is 6V, Zener potential is 5.1V and resistor is 1k ohms.
Two 100V Voltmeters of sensitivities 150 N/V & 250 2/V are connected in series across 80V supply, Their readings are respectively (a) 40V & 40V (b) 20V & 60V (c) 70V & 10OV (d) 30V, 50V
Write down the steps on how to Series Resistors Voltage Division
A current source with parallel resistance can be converted into a voltage source with ---- resistance. series parallel series or parallel O no
Determine the resistances R4 and R5 in Figure 6
The voltage divider shown in the figure has a potential difference (V) between point A and B and a potential difference (VO) between points C and D. What is V FO? A B RM 2R O A. 2 OB. 4 O C.3 OD. S M 2R R :2R C D
True or False: A bimetal is a combination of two pieces of metal that are welded together, each with a different coefficient of expansion.
Help with proper measurement of current through all resistors in the parrallel cirucit below, in multisim.
The circuit in the figure is built on the bread-board. The V2 source is a square wave pulsating between 0-5 V with a 50% duty cycle and a frequency of 1 Hz. The following measurements are taken on the circuit. What is the function of transistor in this circuit? Şekitdeki devre hoard üzerinde kurulmustur kavnağt%0 görev-pervotie 1 Hz. 0-5Vlukbir kare datgadr. Aşağıda betistilen ölçümler devreye ilişkindir. Bu devrede transisterün fonksiyanu nedir? Circuit measurements / Devre ölçümleri Vps= 0.046 V when VGs=5V Vos= 12 V when VGs=0 RD VRD 470 LED STW8B12C D V1 M1 G 2N7002 12 v2 Select one: O a. amplification O b. voltage source O C. switch O d. attenuation O e. current source
Need solution please
in + Find sensitivity of voltage divider of R2 can be changed. Nominal value of R₁-2002 and R2-100 2. Vin - 10 volt. R1 www R2 out