P D le E Loading status in figure q = 4 kN/m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordinoly the normal force at noint E N=?

P D le E Loading status in figure q = 4 kN/m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordinoly the normal force at noint E N=?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Determine the largest load P that can be applied to the frame without causing either the average normal stress or the average shear stress at section a-a to exceed o = 150 MPa and T = 60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. 2m B A 1.5 m a C
Required information Consider the beam and loading shown. If a=8 in, b=9.0 in, c=1 in. For a section at n-n, determine the shear stress at b. A 25 kips 20 in.- 10 in. 25 kips - 20 in.- B a +6 i in.. in. b b a с in.
The internal shear force V at a certain section of an aluminum beam is 11.4 kN. If the beam has the cross section shown (assume a=39 mm, bf=88 mm, tw=t₁=4 mm, d=71 mm), determine: (a) the shear stress T at point H, which is located 39 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a H Answers: (a) TH (b) Tmax= = bf V d MPa. MPa.
If the wide flange is subjected to a shear force of V = 30 kN, Draw the shear stress distribution in the beam and identify the maximum shear stress tmax-. Set w 200 mm. 300 mm A 20 mm 20 mm V 400 mm 20 mm W-
Determine the Global stiffness matrix of the continuous beam shown. Assume EI is 150kN -m² is constant for each element.*For uniform load Q= 48 kN/m*For concentrated load P= 48 kN
P or F value = 36
I need the answer to the question in engineering resistance
9 MPa 7 MPa 5 MP 1. Draw the appropriate Mohr's circle. 2. Get from the circle oi and o2, Umax and its corresponding normal stress (Oevg). Show these points on the circle. 3. Show on the circle the angles 20p and 20s that correspond to the orientation of principal planes and the planes of maximum shearing. 4. Solve point (1c) above graphically using the circle ik. show that your graphical solution is giving the same results as obtained by the analytical equations in point (1c) above.
Need help ASAP Determine the max flexural stress in MPa
A beam has the cross section shown (thin-walled profile). The shear center is at a distance, e = 32.7 mm from the web, IEN = 1134000 mm4. If a force V = 30 kN is applied, passing through the shear center as shown, determine the nearest value of the shear stress in the web at C. |5 mm 3 mm 3 mm 30 mm D 80 mm 30 mm mm E F 55 mm а. 117 МPа O b. 70 MPa Ос. 138 МРа O d. 94 MPa
Problem 2 The lap joint is fastened with four 3/4" diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P 7 in. 8 4 in. 7 81 in. P
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa