9 MPa 7 MPa 5 MP 1. Draw the appropriate Mohr's circle. 2. Get from the circle oi and o2, umax and its corresponding normal stress (Oavg). Show these points on the circle. 3. Show on the circle the angles 20p and 20s that correspond to the orientation of principal planes and the planes of maximum shearing. 4. Solve point (1c) above graphically using the circle ie. show that your graphical solution is giving the same results as obtained by the analytical equations in point (1c) above

9 MPa 7 MPa 5 MP 1. Draw the appropriate Mohr's circle. 2. Get from the circle oi and o2, umax and its corresponding normal stress (Oavg). Show these points on the circle. 3. Show on the circle the angles 20p and 20s that correspond to the orientation of principal planes and the planes of maximum shearing. 4. Solve point (1c) above graphically using the circle ie. show that your graphical solution is giving the same results as obtained by the analytical equations in point (1c) above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
Solve using Mohr circle method
Within few minutes
The right angle bar is supported by a pin at B and a roller at C as shown in figure. The 30 mm diameter pin is in double shear. The shear stress in the pin is limited to 120 MPa. Neglect torsional effect. 400 mm BC The maximum safe value of Pis 30° P 480 mm kN. (Round off to one decimal place)
A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on. c) Determine the relative angle of twist o G-70 GPa # * 2m 450 kN.m B
Handwritten answers only pls.
Use Mohr's circle to determine the principal stresses and the normal and shear force along plane AB.
Using stress transformation equation
len 9
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)