A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on c) Determine the relative angle of twist ona.

A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on c) Determine the relative angle of twist ona.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15900 ksi] rods, and a solid steel [E = 30300 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 28 kips is applied. (1) L2 (1) B P. Answers: i 27.744 ksi. 02 = 4.512 ksi.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
solve correctly and show the complete solution.
25. Design stress is less than the ultimate strength. O 26. If the internal bending moment is negative, the beam bends concave upward. O True False O O True False 27. If the internal shear is negative, the beam bends concave downward, True False
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
The fixed-end bar ABCD consists of three prismatic segments, as shown in the figure. The end segments have cross-sectional area A1 = 840 mm2 and length L1 = 200 mm. The middle segment has cross- sectional area A2= 1260 mm? and length L2 = 250 mm. Loads Pg and Pc are equal to 25.5 kN and 17.0 kN, respectively. (a) Determine the reactions RA and Rp at the fixed supports. (b) Determine the compressive axial force FBC in the middle segment of the bar. A1 - A2 A1 PB Pc A D B L -L1
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
The two bars are used to support load P. When unloaded, joint B has coordinates (0,0). After load P is applied, joint B moves to the coordinate position (-0.65 in., -0.10 in.). Assume a = 20 ft, b = 40 ft, c = 14 ft, and d = 28 ft. Determine the normal strain in each bar. a b C (2) (1) Answer: EAB = i &BC= i P B με με d
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.