In the figure, aluminum [E = 69 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 290 mm² and link (2) has a cross-sectional area of 500 mm². For an applied load of P = 51 kN, determine the rigid beam deflection vg at point B. Assume a = 1630 mm, b = 890 mm, L₁= 2750 mm, and L₂=5120 mm. L₁ (1) a B P b (2) C L2

In the figure, aluminum [E = 69 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 290 mm² and link (2) has a cross-sectional area of 500 mm². For an applied load of P = 51 kN, determine the rigid beam deflection vg at point B. Assume a = 1630 mm, b = 890 mm, L₁= 2750 mm, and L₂=5120 mm. L₁ (1) a B P b (2) C L2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A saw-tooth loading is applied as shown in the figure. The flexural stiffness (EI) of the beam is 1×10³ kN m², determine the following (using the Macaulay's method): the free body diagram q = 24 kN/m² 1 m B 1m 2 m C---- 2 m
Bar AB is rigid and is attached to the steel and aluminum rods as shown in the figure. Before the application of load P, the rigid bar AB is horizontal. Determine the vertical displacement (mm) of point C caused by the load P = 50 kN. A Aluminum L = 3 m A = 300 mm² E = 70 GPa k 3.5 m C P -2.5 m Steel L = 4 m A = 500 mm² E = 200 GPa B
Do not copy.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
For the simply supported beam with the given cross-section, the shear force diagram has been plotted. Determine the maximum shear stress in section e-e of the beam. (A Note: the natural axis is located 65 mm above the toe of the cross-section and I = 5.8133×106 mm4) 160 mm |180 kN 20 mm - N.A B 100 mm 65 mm 500 mm 500 mm 30 mm 30 mm 20 mm V 90 kN Cross-section of the beam -90 kN
3. Rigid member ABD is connected to elastic member CDE as shown. For the given loading, what are the vertical displacements of points A and E? A 20kN dimensions in meters B rigid C T 0.4 D E 0.2 5KN E=7oGPa A=100mm²
= 29,000 For the structure and loading shown below, find the lateral deflection at the top. Use E ksi and I = 250 in4 for all members. Note that in frames, we neglect axial deformation, so you can calculate the deflection at either of the upper corners; the answer will be the same. t. 201 8K 10! 1. What is the deflection at the top in inches (two decimal places) ot
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz=171660000 mm4. If the beam will be subjected to a shear force of V = 120 kN, determine the shear stress at point H, located at yμ = 100 mm above the z centroidal axis. H Hv K Answer: TH= X MPa Ун Ук K Iv
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 12 mm d = 100 mm t = 6.4 mm Additionally: • The area of each pipe is A = 1882 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 171660000 mm4. If the beam will be subjected to a shear force of V = 175 kN, determine the shear stress at point H, located at yH = 100 mm above the z centroidal axis.
The structure shown is supported by a steel rod at B. Specifications of the steel rod L= 2m d=25 mm E=200 GPa Show complete solutions 1. Draw the shear force and bending moment diagrams. 2. Determine the stress in the steel rod at B 3. Determine the deflection at A
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
700 mm (2) 650 mm 80 kN 870 mm (1) 900 mm 650 mm Determine the internal forces and normal stresses in bars (1) and (2). Indicate if it is in Tension or Compression. Also, determine the deflection of the rigid bar in the x direction at C. Bar Properties: Area 1 = 550 mm^2 E1 = 100 GPa Area 2 = 400 mm^2 = 100 GPa E2