A truss is given in the Figure below. The truss is supported by hinges at joint 1, joint 2 and joint 3. (Assume AE constant for all members) Using displacement method (stiffness method), Determine the vertical displacement D2 at joint 4 (use the numbering system indicated in the Figure). D2 of the whole truss is equal to: [Note this information may be used in 4 questions] 8 KN 6 KN 4 m 3 Hinge 3 m Hinge Hinge 3 m

A truss is given in the Figure below. The truss is supported by hinges at joint 1, joint 2 and joint 3. (Assume AE constant for all members) Using displacement method (stiffness method), Determine the vertical displacement D2 at joint 4 (use the numbering system indicated in the Figure). D2 of the whole truss is equal to: [Note this information may be used in 4 questions] 8 KN 6 KN 4 m 3 Hinge 3 m Hinge Hinge 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.3 in2. Find the elongation (in inches) of rod AC caused by the 3088-lb load if x = 10 ft and θ = 56ᵒ. Use E = 29227 ksi for steel. Note: Round off the final answer to four decimal places.
Cho lmao
Consider that a box section is used for the beam loaded as shown in figure. Using flexure and shear stress formula, determine the following Use a = 6 m, b = 3m, c= 344 mm, d = 51mm Distance of the centroid to the outermost fiber of the beam in mm.
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in horizontal direction. The flexural rigidity El, of each member is 10° kNm?, under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be 5 m EI EI 10 m R 50 kN
#4 correct units pls
For a plane truss member, the length is 2 m, E = 200 GPa and area of cross-section is 200 mm². The stiffness matrix coefficient K₁1 with reference to its local axis is A) 200 N/m B 2 × 107 N/m C) 4 x 107 N/m с D) 400 N/m
Problem 2: A beam is made of four rectangular boards nailed together as shown. Note that the nails at C are aligned horizontally, while the nails at D are aligned vertically. Each nail can support a shear force Fs = 100 lb, and the entire beam cross section is subjected to an internal shear force V = 710 lb. (a) Determine the maximum spacing, s, for the horizontal nails. (b) Determine the maximum spacing, s', for the vertical nails. in. 10 in. A 10 in. BL 1 in. KE 1.5 in. 1 in. 2 in.
For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following: Top and bottom members = 1.80 in² Web members = 0.90 in² B 20 kip с 40 kip 6 ft @ 4 = 24 ft D 6 ft
Thankyou.... please solve
Can you help me with my homeowrk?
1.