For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following: Top and bottom members = 1.80 in² Web members = 0.90 in² B 20 kip H с 40 kip 6 ft @4-24 ft 6 ft

For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following: Top and bottom members = 1.80 in² Web members = 0.90 in² B 20 kip H с 40 kip 6 ft @4-24 ft 6 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bars AB, AC, and AD are pinned together as shown in the Horizontal movement of the pin at A is…

A: Please refer the attached image for complete solution. THANK YOU.

Q: The armor shown supports loads of 3 KN. The horizontal elements are 713cm long each. Determine the…

Q: 2. CALCULATE THE FORCES IN ALL THE MEMBERS OF THE REINFORCEMENTS WITH THE METHOD OF THE KNOTS. 40…

Q: For the axially loaded member given below calculate the maximum stress anywhere along the structure…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Determine the force in each members of the truss.

Q: Consider the truss shown in (Figure 1). Suppose that F= 14 kN. Figure 4 kN 6kN G 6kN C…

Q: Determine the thickness of a 2" x 2" angle bar for members BD, BC and DE of truss as shown in the…

A: Consider the FBD of the truss:

Q: For the truss shown, assume a cross sectional area of each member is 3.2 in? a. Calculate the stress…

Q: Find the force exerted on each beam of the truss considering the P force applied

A: For finding the force exerted on each beam of the truss use the method of joints Name each joint…

Q: Consider the truss shown in (Figure 1). Suppose that F = 10 kN. Figure 3 m 4 KN 5KN kN H B C D E F…

A: Determine the force in members CD, CJ and JK of the truss.

Q: A simply supported planar truss is subjected to point loads at joint B and D as shown in Figure 2.…

A: Find the reaction of the truss calculate θ=tan-113.2710=52.99° and α=tan-113.275=69.35°consider ∑…

Q: tension. Consider the truss shown in (Figure 1). Set P = 7 kN, P2 = 9 kN, P, = 13 kN μΑ FBE = Value…

Q: The members of the truss shown below are made of steel (E = 200 GPa) with cross-sectional area of…

A: To determine the elongation of members of the given truss under the given loading, we can use the…

Concept explainers

Load on Structures

Civil engineers primarily deal with beams in their day-to-day applications. A beam is a structural member that resists shear loadings. There are various types of beams such as cantilever beam, simply supported beam, and over the hanging beam. All these beams have a different end and loading conditions.

Question

For the truss shown and loading, determine the axial stress in member BH in ksi. Use two decimal places. Express your answer in absolute value. Assume the sectional areas of the following:
Top and bottom members = 1.80 in²
Web members = 0.90 in²
B
20 kip
с
40 kip
6 ft @ 4 = 24 ft
D
6 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

please show all steps
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 4.7 in., d = 14.1 in., a = 3.7 in., and t= 0.8 in. For a vertical shear force of V = 46 kips, determine the shear flow through the welded surface at B. d В b. Answer: kip/in.
Problem 6.40 Consider the truss shown in (Figure 1). Suppose that F₁ = 4.5 kN and F₂ = 5 kN Figure 1 2 kN of 1 F. B F. C F, D F G -5m-5 m-5 m-5 m 3 kN E dan 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD= -11.9 kN Submit Correct Part B Determine the force in member CF and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCF 9.84 My Answers Give Up Submit μA KN My Answers Give Up Incorrect; Try Again; 5 attempts remaining μA ? Part C Determine the force in member CG and state if this member is in tension or compression. Express your answer to three significant figures and include the…
SITUATION 2: A double-angle tension member, 100 mm x 100 mm x 8 mm is subjected to a tensile load, P= 210 kN. The diagonal member is on a slope 2V:1H and is connected to a supporting beam by a wide tee. S1= 38 mm t1= 16 mm S2= 75 mm t2= 16 mm S3= 100mm t3= 16 mm Allowable strength and stresses: Yield strength, F,= 248 MPa Ultimate Strength, F= 400 MPa Bolt shear strength, F,= 150 Mpa Bolt Tensile Stress, F;= 195 Mpa Bolt Bearing Stress, F,= 1.2Fu Assume that the bolts are equally Loaded. 1. Determine the required "d," of the 3 bolts in shear connecting the double-angle member the wide tee. Round your answer to whole number. 2. Determine the required diameter "d," of the four bolts in tension connecting the wide tee to the flange supporting beam Round your answer to whole number. 3. Design the diameter "d," of the four bolts connecting the wide tee to the flange supporting beam. Round your answer to whole number. 1p S2 S2 t1 t2 t3 S3
The cross-sectional area of each member of the truss is 1.6 in2. Calculate the average normal stresses in members CE. D. 6 ft B F 8 ft 8 ft E 8 ft 6 ft 30 kips 6.833ksi O 6.250ksi O 10.417ksi O 9.362ksi
From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm G a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ Si I P₁ E B S, CIVIL ENGINEERING- STEEL DESIGN ...
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
Consider the Baltimore bridge truss shown in (Figure 1). Suppose that P = 2.5 kN, P2 = 5.5 kN, and P = 4 kN. Figure 2m 2m BCDE F G P, P, P, P, 8@2m- 16 m Part A Determine the force in member EF and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter positive value in the case of tension and negative value in the case of compression. HA 回? FEF= Value Units Submit Reguest Answer Part B Determine the force in member EP and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter positive value in the case of tension and negative value in the case of compression. HA FEP Value Units Submit Request Anser • Part C Determine the force in member KL and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter positive value in the case of…
Problem 2 Compute the axial stresses in the beam AD and in the truss BC. Consider the contribution of the axial load to the bending moment. L = 100 in, αABC= 30 deg,AB = 70 in, E = 10000 ksi,IAD = 10 in*, ABC = 5 in². All the cross-sections are square. W = 10 lb./in. A Pin Pin 5 B Pin Fig. A2.1 D
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A=1480 mm². Assume a-1.5 m, b-6.5 m, and c-3.8 m. If P-55 kN and Q-90 kN, determine the normal stress in each member. L. Answers: JAB" OBC= MPa (C) MPa (T)