The lap joint is fastened with four ¾” diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P in. 4 in. 710 in. P P

The lap joint is fastened with four ¾” diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P in. 4 in. 710 in. P P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Questions a/b c₁ = c₂ = c 5 0.291 10 0.312 20 0.323 40 0.328 200 10 E m 200 10 1. 6.3 kNm torque is applied to a 3m long steel angle with a 200mm x 200mm x 10mm cross section. From tabulated properties for equal angles, the gross cross sectional area of the section is 5090 mm². knowing that G = 77 GPa, determine (a) the maximum shearing stress along line m-m. Provide the answer in MPa with precision n to two decimal points. 2. Determine the angle of twist if 1.7 kNm of torque is applied to the above long angle steel. Provide the answer in Degrees with precision to two decimal points.
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at eachsection. Assume G = 75 GPa. P= 81
1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum value of the principal stress omax at the junction of the flange and the web. 20 kips 20 kips A B 10 ft 2 kips/ft 30 ft- C 10 ft D
With complete Solution pls
7.4 MADE L Fazit On en Colerdo P the an ◄AYAY AT----- TP. TUTT the pre VIVIAVI Det ty ita obo y Survey e fue The courthouse record for a 1902 property survey at Ketchikan, Alaska, lists the magnetic direction of a property boundary as S82°44'W. If the 1902 declination was 37°08'E and the present declination is 26°17'E, find the true bearing and the present magnetic bearing of the property line.
7. (c) A load P of 5000 Kg on the crank pin of the crank shaft as shown in figure is required to turn the shaft at constant speed. The crank shaft is made of ductile steel having yield strength of 2800 Kg/cm2 as determined in simple tensile test. Calculate the diameter of the shaft based on a factor of safety of 2.5. Use maximum shear stress theory. Consider section m-n as critical section. 'm 20cm P 15cm
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze (E, - 15000 ksi) rods, and a solid steel [E2 = 30000 ksi) rod, as shown. The bronze rods (1) each have an area of 0.637 in.?, a length of L - 42 in., and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has an area of 1.228 in.? and a length of L2 - 60 in. If all rods are unstressed before the load Pis applied, determine the normal force in steel rod (2) after a load of P- 30 kips is applied. (2) (1) Rigid bar Answer: F1- kips
An unsymmetric moment of M = 5 kN.m is applied on the cross-section ofan aluminum beam. Find the maximum compressive and tensile normal stresses on the cross-section.Define the orientation of the neutral axis and draw on the cross-section.
D 200 mm 300 mm - 400 mm- A C When force Pis applied to the rigid arm ABC, point B displaces vertically downward through a distance of 0.2mm. Determine the normal strain developed in wire CD.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm E 2а b а —
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
The rectangular bar carries a load of P = 62 kN and is connected to the support bracket with a circular pin. The pin has a diameter of d - 27 mm. Each leg of the bracket has a thickness of t = 16 mm. Determine (a) the shear stress in the pin. (b) the bearing stress between the pin and the bracket. P Rectangular bar Support bracket