The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 18 kN and M = 28 kNm, L1= 1 m, L2 = 6 m, L3= 3 m and a=32 mm. Find, a. by double integration method find the ElS at 2 m from the right support. b. by double integration method the maximum EIS between supports c. If w is spread over the entire length and P and M are interchanged, determine the midspan ElS and deflection by moment – area method y 4a w 10a A M B D la L2 L3 7a

The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 18 kN and M = 28 kNm, L1= 1 m, L2 = 6 m, L3= 3 m and a=32 mm. Find, a. by double integration method find the ElS at 2 m from the right support. b. by double integration method the maximum EIS between supports c. If w is spread over the entire length and P and M are interchanged, determine the midspan ElS and deflection by moment – area method y 4a w 10a A M B D la L2 L3 7a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4. Determine the value of the constant C in the stress function 0 = C{r?(x -0) + p?sin 0 cos 0 - r? cos? 0 tan a required to satisfy on the upper and lower edges of a triangular plate shown below. Evaluate the stress components o, Ty for a vertical section mn. Draw curves for the case a = 20° and draw also for comparison the curves given by elementary beam theory. m a y
2. The maximum bending moment for a 6 meters freely supported beam has been found to be 15.5 kN-m. If the allowable bending stress is 9. 27 MPa, design the beam with respect to bending. Use E = 13, 990 MPa a. Investigate if the computed dimensions will not exceed the allowable shearing stress of 0.90 MPa. b. Investigate if the computed dimensions will not exceed the allowable deflection of L/360.
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“1. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.2 kips/ft, determine: (a) the beam deflection Va at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, Lec = 6 ft, LcD = 6 ft, LDE = 5 ft. В D E LAB LBC LCD LDE Answers: (a) VA = 0.9 in. (b) vc = 0.5| in.
The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 16 kN and M = 24 kNm, L1= 3 m, L, = 5, L3= 2 m and a=35 mm. Find, a. by double integration method find the ElS at the right end of the beam b. by double integration method the maximum Elő between supports c. If w is spread over L-and L7, and P and M are interchanged, determine the midspan Eló and deflection by moment- area method. 4a W 10a M D 7a
I need Vc,Mc
A beam 2.4 m long is simply supported at two points A and B which are 1.44 m apart; point A is 0.36 m from the left-hand end of the beam and point B is 0.6 m from the right-hand end; the value of EI for the beam is 240×10® Nmm². Find the slope at the supports due to a load of 2 kN applied at the mid-point of AB. Use the reciprocal theorem in conjunction with the above result to find the deflection at the mid-point of AB due to loads of 3 kN applied at each end of the beam. Ans. 0.011, 15.8 mm.
2 B W P Assume that the Beam is all the same material. Calculate Q (that we use in the shear stress formula) for the marked position B. P=103.5 mm, J=10.3 mm, W=81.7 mm Q should be given in mm^3 in Whole Numbers.
really really need asap
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
2. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The value of omega "w" is. O 0.171 O 0.128 O 0.085 0.212 0.294 O 0.337
Use Use x = 137 y = 37 a = 6 b = 8 c = 1 answer number 20 and 21 only
solve fast