The cantilever beam shown in Figure A is subjected to load magnitudes of P₂ = 3.0 kips and Py = 8.1 kips. The flanged cross section shown in Figure B has dimensions of bf = 7.1 in., tf = 0.55 in., d = 11.5 in., and t = 0.35 in. Using L = 70 in., determine: (a) the bending stress at point A. (b) the bending stress at point B. (c) the angle for the orientation of the neutral axis relative to the +z axis. Note that positive ß angles rotate clockwise from the + axis. FIGURE A L Z- B tw D FIGURE B | B|Y с

The cantilever beam shown in Figure A is subjected to load magnitudes of P₂ = 3.0 kips and Py = 8.1 kips. The flanged cross section shown in Figure B has dimensions of bf = 7.1 in., tf = 0.55 in., d = 11.5 in., and t = 0.35 in. Using L = 70 in., determine: (a) the bending stress at point A. (b) the bending stress at point B. (c) the angle for the orientation of the neutral axis relative to the +z axis. Note that positive ß angles rotate clockwise from the + axis. FIGURE A L Z- B tw D FIGURE B | B|Y с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown below, b = 6 in and h = 14 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
The cross-sectional dimensions of the beam shown in the figure are a = 4.5 in., b = 5.4 in., d = 4.9 in., and t= 0.31 in. The internal bending moment about the z centroidal axis is M, = -3.85 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. (typ.) Answers: (a) Omax T = psi (b) OmaxC= psi
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
A beam carries concentrated loads at each ends, and a triangular load shown in figure. The beam is a built up shown below. Determine the maximum value of P if the allowable bending stress is1200 psi and the allowable shear stress 200 psi. W=3P P n 4 FT R1 12 FT R2 4 FT
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
The cross-sectional dimensions of a beam are shown. The internal bending moment about the z centroidal axis is M₂ = +3.51 kip-ft. Assume b = 7.125 in., d = 5.25 in. and t = 0.75 in. Determine: (a) the maximum tension bending stress in the beam. (b) the maximum compression bending stress oc in the beam. Answers: (a) OT = i ) oc = i t b y K H ksi ksi.
1. Determine the "t" parameter of cross section of the beam in the figure below (use Navier formula) and the transversal displacement of section A. The allowable stress of the beam material is considered of 100MPa. The cross section of the beam is given in the next figure. q-5KN/m M=4KNM F=3KN L1=3m L2=1m L3=1m 8t M F JA 10t 2t L1 L2 L3 2t 4t
Problem # 4: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and D have a cross-sectional area of 480 mm². For bars B and C, the cross-sectional area is 360 mm². Determine the elongation of bar A when the temperature becomes 60°C. Also, find the axial stress developed in bar C. Use E = 200 GPa and a = 11.7 x 10-6 m/ (m°C). 800 mm D 20 B °8 25000 kg 20 O
12
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
n=8