The truss structure (all members have the same area) carry the loading shown (P = 150 kN) Determine the minimum thickness t (in mm) of the steel member considering allowable vertical displacement of C to be 12mm. Use E-200 GPa. Use Virtual Work Method to solve the problem. D D = 200mm 3m В PV PV 4m 4m

The truss structure (all members have the same area) carry the loading shown (P = 150 kN) Determine the minimum thickness t (in mm) of the steel member considering allowable vertical displacement of C to be 12mm. Use E-200 GPa. Use Virtual Work Method to solve the problem. D D = 200mm 3m В PV PV 4m 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shaft is attached to rigid fixed supports at each end.The maximum shear stress will be equal in both segments when the torque T is applied at B. Determine the dAB. Use 2 decimal places. Use the given sign convention for uniformity.
The question is in the picture. Thanks
Determine the the vertical component of the displacement at point"d" for the shown truss. The areas are given in parenteses (mm²) along each member, and the modulus of elasticity is 200 GPa. (2 500) (1500) 6 m (1 500) (1-500) (000 €) 6 m 180 kN 3m 8 m
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
Please solve correctly
1.) Use Castigliano’s Theorem and determine the vertical displacement of point C. Each steel has cross sectional area of 1500 sq.mm2.) Use Castigliano’s Theorem and determine the vertical displacement of point H. Each steel has cross sectional area of 1500 sq.mm
For the beam shown below, the ratio of stiffness coefficients k41 and k43 is Assume El is constant. -2m- B 4 3m 2
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. =
Determine the force in the member CE of the truss shown. It has F1=13 and F2-3 loaded as shown. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. 2.53 m 2.07 m, -5.4 m F2 F1 2.25 m E F 4 m 3 m B)
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m