A simply.supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed loadwhich can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer mustbe in kN/m. Given: b = 130 mm and d 160 mm.290 mm170 mm

Answered: Image /qna-images/answer/19a0d721-e182-44c0-be65-734accd06156.jpg

A simply.supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed lo which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer mus be in kN/m. Given: b = 130 mm and d 160 mm. 290 mm 170 mm

A simply.supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed lo which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer mus be in kN/m. Given: b = 130 mm and d 160 mm. 290 mm 170 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.8 in., b = 6 in., d = 4.0…

Q: = 23.2 kN, b = 37.5 kN, c = 4.1 m, d = 4,9 m, e = 4,6 m a kN cm - kN B H dm TTTT em e m em FIGURE 1

Q: Problem 4 The horizontal force of p 85 kN acts at the end of the plate. The plate has a thickness of…

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: For the beam and the load shown, use the singularity functions to: Draw the shear diagram Draw the…

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A: The triangular plate with dimensions as shown in the figure below,Horizontal displacement,

Q: The internal shear force at a certain section of a steel beam is V=7.2kN. The beam cross section…

A: Given:- Shear force, V=7.2 KN To find:- a Shear stress at point Hb Shear stress at point Kc Maximum…

Q: From the given figure below : A. Compute the bending stress in the beam, in MPa, shown in the figure…

Q: From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an…

Q: 90 MPa 1. If a point is subjected to the state of stress shown in the figure, determine the…

Q: a B. u R Answer: prad Y = i

Q: Question 2) In the system given in the figure, a distributed load of w=76 kN/m acts on the rod AB of…

Q: The cast iron beam in the figure has an overhang of length b = 2 m at each end. The bending working…

A: The given data is: σt=20 MPaσc=80 MPaσa=2 MPa

Q: If a moment, M=10 ft-kips, is applied to the cross-section about its strong axis, what is the…

A: solve question part g and h, all require data such as depth of neutral axix and moment of inertia…

Q: The individual forces P act on the simply supported beam made of I profile, the dimensions of which…

Q: 主 100 mm 20 mm B 20 mm 80 mm D 0.5m 0.5m 4m 20 mm 60 mm

Q: Question 2) In the system given in the figure, a distributed load of w=85 kN/m acts on the rod AB of…

Q: A cantilever beam with length L = 4 m carries a uniform load w = 29 kN/m. The beam has a rectangular…

A: L=4m b=200mm h=d=400mm

Q: A cantilever beam with length L = 4 m carries a uniform load w = 33 kN/m. The beam has a rectangular…

A: Given, In a cantilever beam, Length of the beam, L= 4m Uniform load, w= 33kN/m Cross section: b=…

Q: Q2 The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a…

Q: A solid circular bar is fixed at point A. Thebar is subjected to transverse load V = 70 lb andtorque…

Q: The internal shear force V at a certain section of an aluminum beam is 8.2 kN. If the beam has the…

Q: The cross-sectional dimensions of the beam shown in the figure are a -4.8 in., b = 6 in., d=4.0 in.,…

A: Given data: Mz=-4.2 kip-ft

Q: The cross-sectional dimensions of the beam shown in the figure area = 5.0 in., b= 6.9 in, d= 4.0…

Q: W B P Assume that the Beam is all the same material. Calculate Q (that we use in the shear stress…

A: The answer has been attached in the form of an image as follows:

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: Draw Mohr's circle and find: 1) Principle stresses and their direction. 2) Maximum Shear stress and…

Q: Figure 3

Q: 8.5 an 250 kN 250 kN 250 kN B D E 0.9 m'0.9 m 0.9 m 0.9 m Fig. P8.5

A: (a)select the most economical metric wide-flange shape that should be used to support the loading…

Q: Vertical rod CD of length L =2 m, cross-sectional area A = 150 mm2 %3D and modulus of elasticity E =…

Q: The cantilever beam is subjected to a concentrated load P. The cross-sectional dimensions of the…

Q: Question 2) In the system given in the figure, a distributed load of w=36 kN/m acts on the rod AB of…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 5.3 in., d = 4.5…

A: Given: The value of a is 4 in. The value of b is 5.3 in. The value of d is 4.5 in. The value of t is…

Q: In урат N 5cm shear and horma Find stress Find moment of inertia, Find the normal stress / Volume…

Q: A cylindrical pipe is attached to a wall at one end (A) and is loaded at its other end (B) by two…

A: The first step is to calculate the polar moment of inertia (J) of the pipe's cross section. The…

Q: y A 100 mm В 20 mm 150 mm 10 mm 20 mm 100 mm

Q: Note : Answer all the Questions Q/ The below cross section is for a beam has a maximum applied…

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A: Truss: Truss is a pin jointed structure which is subjected to vertical loading at the joint only and…

Q: Determine the maximum compressive bending stresses in the beam shown. Let P = 16 I= 100 x 106 mm P…

Q: A cylindrical pressure vessel is supported as shown in the figure. The internal pressure p = 1 MPa.…

A: "Only first part of this question has been attempted. To solve the second please repost the complete…

Q: 3. Solve the following problem The following shaft is subjected to three torsional moments expressed…

A: Step 1:Step 2: Step 3: Step 4:

Q: the stress components ox, es given by elementary bea

Q: to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress…

A: Given:- do=60mm di=50mm T=1.5kN P=205kN To find:- (a) the maximum in-plane shear stress and its…

Q: 2. The maximum bending moment for a 6 meters freely supported beam has been found to be 15.5 kN-m.…

A: Given, L = 6m or 6000 mm M = 15.5 kN-m or 15.5 x 106 N-mm σ = 9.27 MPa E = 13990 MPa

Q: Given the dimensions in the figure, the singular forces P to a simply supported beam made of I…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

A simply.supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load
which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer must
be in kN/m. Given: b = 130 mm and d 160 mm.
290 mm
170 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
Show step by step solution
The cross-sectional dimensions of a beam are shown. The internal bending moment about the z centroidal axis is M₂ = +3.51 kip-ft. Assume b = 7.125 in., d = 5.25 in. and t = 0.75 in. Determine: (a) the maximum tension bending stress in the beam. (b) the maximum compression bending stress oc in the beam. Answers: (a) OT = i ) oc = i t b y K H ksi ksi.
Quicklyyy
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.4 mm and upward by v = 5.8 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 730 mm, α = 25°, and β = 65°.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
2
Within few minutes
Using stress transformation equation
len 9
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.