P= 28 kip-Rigid plateT= 550 kip-ftPlane of weldFigure P6-89 6-89 A thin-walled cylindrical pressure vessel with an inside di-ameter of 4 ft is fabricated by butt-welding 0.6-in.-thick platewith a spiral seam as shown in Fig. P6-89. The pressure in thetank is 360 psi. Additional loads are applied to the cylinderthrough a rigid end plate as shown in Fig. P6-89. Determinea. The normal and shearing stresses on the plane of the weldat a point on the outside surface of the tank.b. The principal stresses and the maximum shearing stress ata point on the inside surface of the tank.

Answered: Image /qna-images/answer/d0c14c3a-0af0-49ad-9147-315e9f465dc4.jpg

Answered: P= 28 kip -Rigid plate T= 550 kip-ft…

Engineering

Mechanical Engineering

P= 28 kip -Rigid plate T= 550 kip-ft Plane of weld Figure P6-89

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

Q: thickness

A: Given G=5600ksi with dia of 2 inches Aluminium alloy G = 4000ksi Torque = 10ft

Q: A static load of 30 kN is applied at the cantilevered beam as shown in the Figure 3.1 The cantilever…

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld of…

Q: 9-25 The weldment shown in the figure is subjected to an alternating force F. The hot-rolled steel…

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. OV The dimensions…

A: To Find : The safe force F in KN. Given : Dimension of perimeter are b=70 mm, c=170 mm, d=70 mm,…

Q: 9-17 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

Q: This weldment is subject to an applied force F=12 kip, weld size h=1/4 in, and the weld is made with…

A: Welding is a fabrication process in which two or more than two parts are fused together using heat…

Q: The assembly shown in the figure consists of rod (1) and tube (2), both made of steel (E = 30,000…

Q: Required Information A steel bar of thickness h, to be used as a beam, is welded to a vertical…

A: To determine:The allowable force Given:The allowable shear stress is The dimensions for the…

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If…

Q: veld can sustain is (kN m)

Q: Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa…

A: Compressive stress on the x-axis, Tensile stress on the y-axis, The value of the angle,

Q: Required information A steel bar of thickness h, to be used as a beam, is welded to a vertical…

A: The allowable shear stress is the dimensions of the parameter is

Q: Q1/ Figure below shows a welded steel bracket loaded by a static force F. Estimate the safety factor…

A: Given Data Height of the weld is: w=6 mm Distance from fixed end is: d=125 mm width of the weld…

Q: Q1/ Figure below shows a welded steel bracket loaded by a static force F. Estimate the safety factor…

Q: Two steel plates having yield point stress of 350 N/mm2 are joined together by double fillet welds…

Q: A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A: Refer to the picture belowExplanation:

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Introduction: The load-bearing capability of a weld relates to how much load it can withstand before…

Q: A plate I m long 60 mm thick is welded to another plate at right angles to each other by 12 mm fil-…

Q: steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In…

Q: In the figure shown, shaft A, made of AISI 1020 hot-rolled steel, is welded to a fixed support and…

A: Given data As shown in following figure , shaft A made of also 1020 hot rolled steel is welded to a…

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: The figure shows a weldment just like that for Probs. 9-17 to 9-20 except there are four welds…

A: Given data as per the question No. of weld of the object =4

Q: Considering Figure 20-8 (textbook), the torsion geometry parameter, Jw, for case 6 when b=6 and d=9…

Q: (1) The figure shows a horizontal steel bar 3/8 in thick loaded in steady tension and welded to a…

A: Given data: b=2ind=2 inh=516int=38 inτallow=20 kpsi Need to determine the allowable force.

Q: nt is shown E

A: `

Q: A rectangular plate (0 =20") is formed by welding two triangular plates shown in figure. The plate…

Q: A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A: The allowable force, F, on the weld is approximately 252.84 kN.Explanation:Step 1: To find the…

Q: Calculate ly the moment of inertia for the composite section about the x-axis. in4 ENTER Calculate…

Q: A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The…

A: Write the expression of strength of parallel fillet weld. P1=0.707sl1σt ...... (1) Write the…

Q: in the figure is desigr t welds ae required as gh the pointsA&E

Q: Two welds, having length Li=150 L2=200 are required to attach a e to a column, as shown in Figure…

Q: A shaft with two diameters connected by a fillet is shown below. In the diagram, di = 45 mm, d2- 50…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

100%

P= 28 kip
-Rigid plate
T= 550 kip-ft
Plane of weld
Figure P6-89

6-89 A thin-walled cylindrical pressure vessel with an inside di-
ameter of 4 ft is fabricated by butt-welding 0.6-in.-thick plate
with a spiral seam as shown in Fig. P6-89. The pressure in the
tank is 360 psi. Additional loads are applied to the cylinder
through a rigid end plate as shown in Fig. P6-89. Determine
a. The normal and shearing stresses on the plane of the weld
at a point on the outside surface of the tank.
b. The principal stresses and the maximum shearing stress at
a point on the inside surface of the tank.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Check bolt spacing, edge distances, and bearing for the connection shown in Figure below
Riveted and Welded Joints
the is allowable because member metal is incorporated into the welds? (Ams/11.3 kip) (4) A 5/16 -in steel bar is welded to a vertical support as shown in the figure. What is the shear stress in the throat of the welds if the force F is 32 kip? (Ans/181 kip) 2 in 2 in
B A bracket shown in the figure is designed to carry a dead weight of W = 15000 N. What sizes of fillet welds ae required at top and bottom of the bracket. Assume the forces act through the points A & B. The permissible strength of the-weld is %3D 150 N/mm. A: A 25mm 75 inm B B, w = 1500UN B, 50mm
A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MPa , Trivet= 102 MPa and Obearning =330MPA. Assume diameter of hole = 25mm 022mm rivet Plan P section -300mm-
are of 10 mm size and the weld length is 30 mm. loading F as shown in figure. Both legs of the fillets considering the minimum throat of the weld, the A fillet welded joint is subjected to transverse loading Fas shown in figure. Both legs of the fillets ere of 10 mm size and the weld length is 30 mm. If the allowable shear stress of the weld is 94 MPa, considering the minimum throat of the weld, the maximum allowable transverse load in kN is F
A welded joint, as shown in figure below, is subjected to an eccentric load of 2500 N. Find thesize of the weld, if the maximum shear stress in the weld is not to exceed 50 N/mm2
A beam is supported and loaded as shown in the figure. Data: L = 1000 mm, c = 300 mm, f = 100 mm, D = 100 mm, d = 80 mm. The beam consists of different parts that are welded, and the fillet weld size a is 4 mm. The load q is 2 kN/m, and P = 10 kN. Calculate the maximum stress in the welds.
A steel plate, 80 mm wide and 10 mm thick, is joined toanother steel plate by means of a single transverse anddouble parallel fillet welds, as shown in figure. The strengthof the welded joint should be equal to the strength of theplates to be joined. The permissible tensile and shearstresses for the weld material and the plates are 100 and 70N/mm2 respectively. Find the length of each parallel filletweld. Assume that the tensile force passes through the centre of gravity of three welds.
The carrier plate material St52 (S355) given in the figure below is welded to the body. combined. F1 = 4 kN and F2 = 40 kN static forces act on the plate. Source I. Quality (v2 = 1), no impact (v3 = 1), weld thickness a = 5 mm, safety coefficient s = 2 and weld seam coefficient v1 = 0.8 will be taken. Find out whether a = 5 mm weld seam thickness is sufficient or not, according to the data in the figure and above.
Problem 5: (D2) You are an engineering intem at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design brass eye-bolt, shown in Figure.7, to confim it's not exceeding its yield strength. The bolt dimensions are (d, R) = (8, 12) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section B – B. located at an angle of 40° from the positive x-axis, when the load is F = 0.4 kN. R FA B
Figure 4 shows a rectangular hollow steel bar welded to a vertical member. The bar has to support a IkN load at its free end. Fillet welds extend all around the outer periphery of the bar. Assuming that the Distortion Energy Theory is applicable, i.e., Say = 0.58 x S, determine the required weld size using a welding rod with S, = 330 MPa and a safety factor of 3 based on yielding. Neglect the weight of the rectangular bar. 1 kN 60 2 25 15 Figure 4 with all dimensions given in millimetres