The assembly shown in the figure consists of rod (1) and tube (2), both made of steel (E = 30,000 ksi). The tube is attached to a fixed support at C. A rigid end plate is welded to the tube at B, and the rod is welded to the end plate. The rod is solid with a diameter of d₁ = 0.400 in. The tube has an outside diameter of D₂ = 2.50 in. and a wall thickness of 1₂ = 0.110 in. The dimensions of the assembly are a = 57 in. and b = 39 in. Determine the horizontal deflection at rod end A for an applied load of P = 3.2 kips. End plate Tube (2) Jd₁ Rod (1) Fixed support

The assembly shown in the figure consists of rod (1) and tube (2), both made of steel (E = 30,000 ksi). The tube is attached to a fixed support at C. A rigid end plate is welded to the tube at B, and the rod is welded to the end plate. The rod is solid with a diameter of d₁ = 0.400 in. The tube has an outside diameter of D₂ = 2.50 in. and a wall thickness of 1₂ = 0.110 in. The dimensions of the assembly are a = 57 in. and b = 39 in. Determine the horizontal deflection at rod end A for an applied load of P = 3.2 kips. End plate Tube (2) Jd₁ Rod (1) Fixed support

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel plate 5/16 in. thick is embedded in a horizontal concrete slab and is used to anchor a high-strength vertical cable as shown in the figure below. The diameter of the hole in the plate is 0.75-inches, the ultimate strength of the steel used is 36 ksi, and the ultimate bonding stress between the steel plate and concrete is 300 psi. The designers considered a factor of safety of 3.60 is desired when P = 2.5 kips. Address the following: (a) Identify three potential failure modes for the complete system. For each mode develop a sketch which idealizes the mode of failure. (b) If you where required choose dimensions for the plate ("a" and "b"), how would you size these dimensions? (c) For one of the failure modes identified above, perform an analysis to determine adequate plate dimensions ("a" and "b") to support the required load of 2.5 kips with the established factor of safety. in. AP Sl 4 in.
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm a=9.6 TAKE 60.a mm 50 mm D Yatağı 100 mm t mm F=100 kN
The bell crack mechanism shown in Figure is in equilibrium for an applied load of F1- 15KN at A and F2 at C. The pin at B has a diameter of 12mm. The thickness of the bell crank is 8mm while the support bracket has a thickness of 6mm. The bell crank and the support bracket each have an ultimate bearing strength of 550 MPa. a = 300 mm; b = 150 mm ; c = 100 mm; e = 65° %3D %3D 30° (2) Bell crank B F2 b. a F1 H-8 mm BLI Bracket 6 mm mm Connection detail Determine the magnitude of the resultant reaction force acting at pin B. (in KN).
Three identical circular disks A, B, and C arewelded to the ends of three identical solid circular bars(see figure). The bars lie in a common plane and thedisks lie in planes perpendicular to the axes of the bars.The bars are welded at their intersection D to form arigid connection. Each bar has diameter d1 = 0.5 in.and each disk has diameter d2 = 3.0 in.Forces P1, P2, and P3 act on disks A, B, and C,respectively, thus subjecting the bars to torsion. IfP1 = 28 lb, what is the maximum shear stress τmax inany of the three bars?
For a given Data of the riveted joint shown in the figure: Given: Diameter of each rivet = 3/4 inch Maximum allowable shear stress of rivet = 96.53 MPa 3. Maximum allowable bearing stress of plate = 124.11 MPa %3D Yield Strength of the key = 45 MPa Ultimate Strength of the key = 128.5 MPa %3D Determine the maximum safe value of P that can be applied to both ends in Kips or Kilo pound. The figure below: 4 in P 7/8 in 7/8 in
L = 0.3m A = 20 x 6 mm E= 70 GPa allowable stress = 120 MPa 0.6 m 0.4 m 0.2 m Rigid bar D C W 0.5m 40 x 6 mm 50 GPa wable stress = 80 MPa 16 mm dia. bolt with allowable s 6 mm 80 MPa in bearing and 60 MPa The rigid bar A,B,C,D shown in figure is connected to the ground by a hinge at B and to Magnesium bar at A, Aluminum bar at C. the properties of the bars are shown on the figure. all the connections are using 16 mm bolts in single shear. Determine the maximum safe load W that can be applied. Determine the final position of point D.
A solid with a diameter of d=10 mm subjected to loads in the figure. the elongation affixed to the bar in the 1 and 2 direction unit shape of ε1=200µ and ε2=50µ from wires, respectively. P applied as the replacement values are measured Calculate the force and torque T. (E=200 GPa, ν=0,3)
View Policies Current Attempt in Progress The assembly shown in the figure consists of rod (1) and tube (2), both made of steel (E = 30,000 ksi). The tube is attached to a fixed support at C. A rigid end plate is welded to the tube at B, and the rod is welded to the end plate. The rod is solid with a diameter of d₁ = 0.380 in. The tube has an outside diameter of D₂ = 2.50 in. and a wall thickness of t₂ = 0.115 in. The dimensions of the assembly are a = 68 in. and b = 39 in. Determine the horizontal deflection at rod end A for an applied load of P = 4.3 kips. Part 1 F₁ i D₂ Save for Later B kips End plate a Tube (2) 12 C ↑ b Based on an appropriate FBD, determine the axial force F₁ in rod (1). Use the sign convention for internal axial forces discussed in Section 5.3. Rod (1) Fixed support Attempts: 0 of 1 used Submit Answer
The pin-ended wrought-iron pipe shown in the figure below has outer diameter D, inside diameter d, and length L; it supports an eccentric load P based on a safety factor of n. Find the largest allowable eccentricity e. Given: D = 190 mm, d = 170 mm, L = 3.5 m, P = 430 kN, n = 1.4, E = 190 GPa, 0yp = 210 MPa.
The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy= 300 Ibf and Fx= Fz= 0 lIbf. The length of the rod DC denoted by L is given to be 11 in. The length of the rod AB denoted by L2 is given to be 10 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 2 in L2 in 1-in dia tin R. B | 2 in C l-in dia. Itin dia. -in dia. Li in
In the figure, a solid copper rod with an expansion coefficient α copper = 165.10-7 1/ºC is 20 mm in diameter. It is placed in a steel pipe with an outer diameter of 30 mm with an inner diameter of 2 mm larger than this bar and an expansion coefficient αsteel = 125.10-7 1/ºC, and is combined with a rigid plate from the top so that they move together. Find the stresses that will occur in steel and copper when the system is heated with a temperature difference of Δt = 80 ºC. (Esteel=200 GPa, Ecopper=100 GPa)
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 150 in. Rod (1) has a length of L₁ = 99 in. and a cross-sectional area of A₁ = 0.55 in.². Rod (2) has a length of L₂ = 96 in. and a cross-sectional area of A₂ = 0.95 in.². Rigid bar ABC is to remain horizontal under a load of P = 35 kips. Determine the distance x from joint A to the location of load P so that bar ABC remains horizontal. L Answer: X= i (1) eTextbook and Media Save for Later x in. B (2) L2 Attempts: 0 of 5 used Submit Answer