A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure.The allowable shear stress in the weld is 148 MPa.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.FoddkbThe dimensions for the parameters in the figure are given below.b = 52 mmc=138 mmd = 52 mmh = 5 mmWhat is the allowable force, F, on the weld?The allowable force, F, on the weld iskN.

The allowable force, F, on the weld is approximately 252.84 kN.Explanation:Step 1: To find the…

Answered: A steel bar of thickness h, to be used…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The elongation of a bar of uniform cross section subjected to an axial force is given by the equation (omega)= PL/AE What are the dimensions of E if (omega) and L are lengths, P is a force, and A is an area?
Hi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure attached). Can you help me answer all the questions below? Especially the one about the bending moment and shear force. The Figure 2 attached is a simplified structure to undertake a structural analysis on a concept design for a low cost stroller/buggy for children. The buggy consists of a number of metal sections that are pin-jointed together. The buggy is designed to accommodate a child of mass no more than 20 kg, sat on the seat which is supported at four points (Fc) on the frame of the buggy. Assume that the weight of the child is equally distributed across all of the points indicated on Figure 2 as Fc. Assume that there are no additional forces applied to the handle of the buggy, that the buggy is static (stationary) and that the buggy, and the elements of the frame have no mass. At points A and G, there are roll supports. At Points B, F and D there are the pin supports. I am required…
Q3
Please help. Written on paper not typed on computer or keyboard please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Learning Goal: A material is homogenous and isotropic when it has a modulus of elasticity that does not vary with direction and it has uniform properties throughout. When a point in a material is subjected to only normal stresses in three dimensions, but they are not necessarily equal, the state is called triaxial stress. When the response of the material is linear elastic, the strains along the three axes can be calculated using a generalized form of Hooke's law. Each strain depends on all three stresses because of the Poisson effect. €1 Figure 1 [0₂ - V (O₂ +0₂)] a 1 of 1 A cube is subjected to stresses with magnitudes a = 16 MPa, b = 26 MPa, and c = 5 MPa (Figure 1). What is the strain in the y-direction? Let E = 200 GPa and v= 0.26. Express your answer to three significant figures. ► View Available Hint(s) Submit VE ΑΣΦ Part B - Change in volume f change in volume = vec The cube from Part A originally has side length 3.2 cm . What is the change in volume of the cube under the given…
When a bar of 22 mm diameter is subjected to an axial pull of 60 kN the extension on the 49 mm gauge length is 0.1 mm and there is a decrease in diameter of 0.013 mm. Calculate the Young's Modulus. Provide your answer in GN/m2 to the nearest whole number.
Rigid bar ABCD is loaded and supported. Steel [E=30,000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.625 in.2 and bar (2) has a cross-sectional area of 1.25 in. 2. After load P is applied, the strain in bar (2) is found to be 900 με. If there is a clearance of 0.05 in. in the pin connection at C, determine: (a) the stresses in bars (1) and (2).(b) the vertical deflection of point D.(c) the load P.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS