Required InformationA steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in thefigure. The allowable shear stress in the weld is 27 kpsl.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Foddhc = 6 Ind=2 Inh = 0.325 in|FThe dimensions for the parameters in the figure are given below.b=2 inUsing electrode E7010, a bar that is hot-rolled 1020, and a support that is hot-rolled 1015, find the allowable force, F, on the weld.The allowable force, F, on the weld isklp.

To determine:The allowable force Given:The allowable shear stress is The dimensions for the…

Required Information A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. The allowable shear stress in the weld is 27 kpsl. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 여 d → F The dimensions for the parameters in the figure are given below. b=2 in c=6 In d=2 in h=0.325 in Using electrode E7010, a bar that is hot-rolled 1020, and a support that is hot-rolled 1015, find the allowable force, F, on the weld. The allowable force, F, on the weld is [ klp.

Required Information A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. The allowable shear stress in the weld is 27 kpsl. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 여 d → F The dimensions for the parameters in the figure are given below. b=2 in c=6 In d=2 in h=0.325 in Using electrode E7010, a bar that is hot-rolled 1020, and a support that is hot-rolled 1015, find the allowable force, F, on the weld. The allowable force, F, on the weld is [ klp.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLS ANSWER URGENT, THANK YOU.
Q2: The rigid beam shown in figure is fixed to the top of the three rods. The two outer rods are aluminum [Eal=70 GPa] and the middle rod is steel [E200 GPa]. After the load (P) is applied, the stress in steel rod is found to be (24.5 MPa). Determine: 4. The stress in aluminum rod. 5. The load (P). 6. The deformation of aluminum rod. 2P 50 mm ווז וn 30 30 mm- 300 mm - 0.5 m - 0.5 m
A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.3 MPa in the x-direction and a tensile stress of 13 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. Weld Lütfen birini seçin: a. 10.664 MPa/5.50 MPa b. 0.3131 MPa/4.93 MPa c. None d. 0.0358 MPa/5.50 MPa e. 9.3175 MPa/6.09 MPa
) find the required fillet welds size if the allowable shoar stress is 9.4 KN/Cm fot the figure below Talls 190m 450 mm A Ans: h=5.64 mm =30 KN 250 *-F=l。ト %3D
Express the final answer in 4 decimal places.
Pls box ur answer thx u
A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being concerned for the strength of the weld, you need to find the state of stress (normal stress and shear stress) in the plane of the weld for an applied load of 400kN. Draw your result on a stress element. 57° 400 kN 400 kN 100 mm