A beam is supported and loaded as shown in the figure. Data: L = 1000 mm, c = 300 mm, f = 100 mm, D = 100 mm, d = 80 mm. The beam consists of different parts that are welded, and the fillet weld size a is 4 mm. The load q is 2 kN/m, and P = 10 kN. Calculate the maximum stress in the welds

Q: A steel cantilever beam is made of two T-shaped structures welded to each other as shown in the…

A: given; q=2MN/mσ=150MPalength (L)=L1+L2                  =1+.5                   =1.5m

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. OV The dimensions…

A: To Find :  The safe force F in KN. Given :  Dimension of perimeter are b=70 mm, c=170 mm, d=70 mm,…

Q: The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the…

A:

Q: 9-17 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A:

Q: This weldment is subject to an applied force F=12 kip, weld size h=1/4 in, and the weld is made with…

A: Welding is a fabrication process in which two or more than two parts are fused together using heat…

Q: The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1…

A:

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If…

A:

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A: Solution: Maximum shear stress is given by, Solid tube,…

Q: Required information A steel bar of thickness h, to be used as a beam, is welded to a vertical…

A: The allowable shear stress is the dimensions of the parameter is

Q: The arm in the figure is combined with a rod with a diameter of d=30 mm and a neck (corner) weld…

A:

Q: e vessel, as shown in the bolts along with rer plate thickness. e tensile stress for MPa and for…

A: solution of Question 1

Q: Two steel plates having yield point stress of 350 N/mm2 are joined together by double fillet welds…

A:

Q: Find the primary, secondary and resultant shear stress of following welding. b=2", d=2", h= 1/4".…

A: To find The primary, secondary and resultant shear stress. Given  The force F is 1000 lbf. The…

Q: 2- Design a weld connection for an UNP 280×80x9 of S 355 (f,= 355 MPa and f,= 470MPA) steel…

A:

Q: The weldment shown in the figure is subjected to a static force of 100 kN. The hot-rolled steel bar…

A: (a) Calculate the weld metal strength. FW=0.7072b+dh×τallowFor electrode E6010,τallow=200…

Q: The cylinder in the figure below consists of spirally wrapped steel plates that are welded at the…

A: Given:The thickness of the wall is .The axial load is .The outside diameter of the cylinder is…

Q: The figure shows a weldment just like that for Probs. 9-17 to 9-20 except there are four welds…

A: Given data as per the question No. of weld of the object =4

Q: Considering Figure 20-8 (textbook), the torsion geometry parameter, Jw, for case 6 when b=6 and d=9…

A:

Q: Asteel bar of rectangular cross section dimension as -shown in fig- below.This bar is Connected…

A: Given, Allowable shear stress = τal = 35 N/mm2

Q: A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A: The allowable force, F, on the weld is approximately 252.84 kN.Explanation:Step 1: To find the…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

A:

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A:

Q: Calculate ly the moment of inertia for the composite section about the x-axis. in4 ENTER Calculate…

A:

Q: A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The…

A: Write the expression of strength of parallel fillet weld. P1=0.707sl1σt    ...... (1) Write the…

Q: Yivt(d) Hiw@. what alead (F) مهمل required to sperate the riveted plates shocun in frigure? & =(80…

A:

Q: Two welds, having length Li=150 L2=200 are required to attach a e to a column, as shown in Figure…

A:

Q: The Figure shows a 0.75-in-thick AISI 1020 HR steel bar subjected to a load of (F = 1.4 kip) and…

A: Given: σy=30kpsi b=d=2in h=5/16in Load (F)=1.4kip Solution: Due to the symmetry of the weld joints,…

Q: Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: Force ,F=60000 lbAllowable stress,Size of the weld ,h=1/4 inchTo determine:a)the method used to…

Q: column 350 3 kN 2 kN beam 80 140

A:

Q: Find. The weld sizé W for the welted.join.shawwi figure ..in below where aaill =3.MPag Tall=l.5 Mfa…

A:

Q: 2. For the given welded bracket shown, design the required size of weld needed to resist the given…

A: To Find:The maximum force on the weld.Given:The eccentric load is the distance

Q: The beam shown in Fig.3 is welded to a fixed support. Find the maximum combined stresses in the weld…

A:

Q: (1) What are the methods used to obtain a good weld when welding steel when the carbon content is…

A: 1. to determine the method used to obtain good weld for high carbon steel

Q: B A bracket shown in the figure is designed to carry a dead weight of W = 15000 N. What sizes of…

A:

Q: A 3/4-in. horizontal steel bar loaded at constant tension and welded to a vertical support is shown…

A: WELDING SYMBOL: It indicates the the complete welding for the joint design that is bevel weld symbol…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.