ompounds 2,4 Dinitrophenylhydrazones Mix 2.5 mL of 2,4-dinitrophenylhydrazine in phosphoric acid and 25 mg of the unknown. Warm in a water bath for 5 min and let crystallization proceed. Collect the product by suction filtration and wash the crystals with cold water. Recrystallize from ethanol and let it dry until next time. NHÁNH, N-NH- -NO₂ R☑ R✗ R' NO₂ R' O₂N

ompounds 2,4 Dinitrophenylhydrazones Mix 2.5 mL of 2,4-dinitrophenylhydrazine in phosphoric acid and 25 mg of the unknown. Warm in a water bath for 5 min and let crystallization proceed. Collect the product by suction filtration and wash the crystals with cold water. Recrystallize from ethanol and let it dry until next time. NHÁNH, N-NH- -NO₂ R☑ R✗ R' NO₂ R' O₂N

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter12: Isopentyl Acetate (banana Oil)

Section: Chapter Questions

Problem 2Q

See similar textbooks

Similar questions

What is the chemical reaction when completing extraction experiment and using 100mg Benzoic Acid, 2ml H2O and CH2Cl2 each? What is the chemical reaction when completing extraction with 4-chloroaniline and adding in HCl?
Greetings, Can you please provide the solution to the attached question. Thank you
A student dissolved a mixture of benzoic acid (C6H5CO₂H), phenol (C6H5OH) and 1,4 dimethoxybenzene (CH3OC6H4OCH3) in t-butyl methyl ether. She extracted the solution with 5% aqueous sodium bicarbonate, and labeled the extract A. She then extracted the ether solution with 1 M aqueous sodium hydroxide, and labeled that extract B. She added 12 M aqueous HCl to these two extracts, producing a white precipitate in each. The precipitate obtained from solution A is probably... dimethoxybenzene benzoic acid t-butyl methyl ether Ophenol NaCl
Suggest possible crystallization solvents for the following compounds. Use IMF to predict the type of solvent each compound should be soluble in. Then, find the melting point and solubility of compounds in the handbook, and choose s recrystallization solvent
A Grignard reaction of phenylmagnesium bromide with 3-pentanone gives 3-phenylpentan-3-ol as the major product. The crude product contains the 3-phenylpentan-3-ol product, unreacted 3-pentanone, and biphenyl (a side product). A developing solvent is found that separates the mixture into three spots on a silica gel TLC plate. Considering the functional groups present, predict which compounds would have the smallest and largest Rf values. Briefly justify your answer.
What will be the aluminium oxide ( Al;O; ) content of your preparation per 5ml Al;O3 content of the gel is 50.0% ?
a) To a solution of 10 g (60 mmol) of 3-nitrophenylacetic acid in 120 ml of ethanol were added 20 ml of a saturated 5 solution of hydrogen chloride in ethyl acetate and the mixture was heated at reflux for 4 hours, cooled and left to stand at room temperature for 18 hours. The mixture was evaporated and the residue was partitioned between 120 ml of diethyl ether and 100 ml of saturated aqueous sodium 10 bicarbonate solution. The organic phase was dried over magnesium sulfate, filtered and evaporated to give 10.3 g. (82%) of ethyl 3-nitrophenylacetate as a pale yellow oil. [NMR spectrum (250 MHz) 81.25(t) (3H), 83.68(s) (2H), 84.6(q) (2H), 86.5-86.7(m) (3H), 87.09(dd) (1H)].
3 Draw a flow chart to shows the strategy for separation of three compounds: Phenanthrene and 4-Aminoacetophenone and 1,4-Dibromobenzen and dissolve mixture is Diethyl ether. add NaOH (1M) and (6M) to the aqueous layer and ether layer..
Melting point range Recrystallized Phenacetin 95-100 Recrystallized Phenacetin + Reference Phenacetin 110-115 Recrystallized Benzil 92-95 Recrystallized Benzil + Reference Benzil 94-98 Questions: 1. What does your melting point say about the purity of your phenacetin sample? Justify your answer using the characteristics of mixed melting point. 2. What does your melting point say about the purity of your phenacetin sample? Justify your answer using the characteristics of melting point. 3. What are two characteristics of a good recrystallization solvent for a given compound? 4. Given a solid sample that contains impurities, how would you determine which solvent to use for a recrystallization? Describe how you would do this in the laboratory. 5. Clearly explain the difference between a recrystallization and a precipitation.
5
OC1 O D.4 QUESTION 10 An impure aqueous sample of I was extracted with ether. The ether layer was then extracted with 0.1 M HCI. Which layer will contain the compound after the second extraction? NH2 O A. both, because I is soluble in both, 0.1 M HCl and ether. O B. ether layer O C. none, because I doesn't dissolve in ether in the first extraction. O D. aqueous layer (0.1 M HCI) QUESTION 11 Which carbonyl compound CANNOT form an enolate ion in an aldol condensation reaction? Click Save and Submit to save and submit. Click Save All Answers to save all answers. pe here to search PriSc F10 F11 F12 F7 F8 F9 Esc F3 F4 F1 & 23 7 8 4 W E T ab G H J K oSLk C VBN M All Co
5. The pKas of chemicals HX and HY are 5.0 and 7.0 respectively. The pKa of carbonic acid H,CO, 3. is 6.0. If you made up an ether solution of chemicals HX and HY in a separatory funnel, and then added an aqueous solution of sodium bicarbonate NaHCO3 to that separatory funnel, would both HX and HY stay in the ether layer? Or would either or both of them transfer into the aqueous layer? If one goes into the water layer, will it be in its neutral HX/HY form, or in it's deprotonated anionic form? ilter HX: ether layer or water layer? If in the water layer, in HX or X- form? Explain HY: ether layer or water layer? Explain.