Example 3.4. A uniform wheel of 600 mm diameter, weighing 5 kN rests against a rigid tangular block of 150 mm height as shown in Fig. 3.8. 600 mm A 150 mm Fig. 3.8. Find the least pull, through the centre of the wheel, required just to turn the wheel over the ner A of the block. Also find the reaction on the block. Take all the surfaces to be smooth.

Example 3.4. A uniform wheel of 600 mm diameter, weighing 5 kN rests against a rigid tangular block of 150 mm height as shown in Fig. 3.8. 600 mm A 150 mm Fig. 3.8. Find the least pull, through the centre of the wheel, required just to turn the wheel over the ner A of the block. Also find the reaction on the block. Take all the surfaces to be smooth.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a beam is supported by a pin support at A and a roller support at B. For this question, leave your answer in terms of the variables w and L. (a) Using equilibrium of the full beam, find the support forces at A and B. (b) First section: Make an arbitrary cut between points A and B. Take the distance of the cut to be x along the beam from point A. Draw the free-body diagram for the left section and find functions for the internal shear force, V(x), and bending moment, M(x), in the section of the beam between A and B. (c) Second section: Repeat part (b) for the section of the beam between B and C. Take x to still be the distance from point A. (f) Find the value of x at which V(x) = 0. The internal bending moment reaches a maximum at the same point as V(x) = 0. Find the maximum bending mo- ment. pin Sketch the shear and bending moment diagrams. B L W C roller
The lid shown has a mass, m = 60 kg, and is held in position by rod AB. The rod is held in place by rounded surfaces at A and B, where B is right at the edge of the lid. The hinges at C and D rotate smoothly and only the hinge at C provides a reaction force along its axis (the x-direction). a = 950 mm, b = 300 mm, c = 55 degrees Determine A) Reactions at hinge C and D B) Reaction force in rod AB C) The minimum coefficient of friction that is needed between the rod and the lid to maintain this position
Draw the free-body diagram of the smooth uniform bar shown in Fig. 2. The bar has a mass of 20 kg.
A 120 N is at rest on a rough in a line making an angle of 20° with the horizontal. The roller has a radius of 0.40 m. as indicated in the figure. a.Calculate the force P that is required to push the roller at rest on the rough incline surface. b. Calculate the normal reaction at the point of contact between the roller and the rough inclined surface. c.Calculate the force P required to pull the roller at rest on the rough incline surface.
1) Determine the reaction at roller A. Express your answer to three significant figures and include the appropriate units. 2) Determine the horizontal and vertical components of reaction at pin B(Bx,By) . Express your answers in newtons to three significant figures separated by a comma.
The figure shows a mechanism that raises packages in a transfer mechanism. A 500-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank 02A and the force in member AB The weights of the links are negligible. 30mm 450mm 500N 220 mm B 374 mm 374 mm The angular velocity of the link O,BD in rad/s is = The magnitude of the velocity of point D in m/s is =
Consider a steel cube with side length L and each of its faces normal to the orthogonal axes x, y, and z as shown below. If the cube is subjected to a constant tensile force T along the x-axis and the faces along the y- and z- axes are left free and unsupported, which of the following best describes what is expected to happen? Z Select one: O A. The cube will expand along the x-axis and compress along the y- and z-axes. B. The cube will expand along the x- and y-axes and will not deform along the z-axis. O C. The cube will expand along the x-axis and will not deform along the y- and z-axes. O D. The cube will compress along the x-axis and expand along the y- and z-axes.
A horizontal bar 10m long and of negligible weight rests on rough inclined asshown in figure. If the angle of friction is 15, how far from A may the 200 kNforce be applied before motion impends?
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
A rectangular gate (6m x 4m) is e hinged at A and supported by a stopper as shown. Find the reaction Lé at the hinge neglecting the weight of the gate
Find the force on each member of the truss and indicate if they are under tractionor compression. I am having difficulty in the decompositions of forces. if you can, put this in detail.I already found the reaction forces and they are in the image below. Thank you very much in advance