An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft

Q: Member ABCD has the following weight and dimensions: Weight of ABCD = 150 N h1= 0.8 m h2= 1.8 m h3=…

A:

Q: Find the force generated by the deltoid (right arm) if: His arm length (d) is: 0.84 m The COG of the…

A: Arm Length d=0.84mCOG=37%Wa=7.9NWw=126NAngle=90°Insertion=0.17mAngle for line of pull=11°…

Q: ne correct free-body he weight? Explain

A: Given data A member is given in Which a load is acting at the end Required Free body digram

Q: Force F acts on the frame such that its component acting along member AB is 700 Ib, directed from B…

A: FORCE  Strength is any effect that changes the object's movement while unopposed. A force may modify…

Q: 1) A drawbridge has mass M and length L and is approximately uniform. It has a hinge at the right…

A:

Q: rque Problem diagram below shows the lower leg being held in a stationary. The torque ng to turn the…

A: Angle made with horizontal = 50° Weight of leg WL = 90 N Weight of barbel Wb = 120 N Quadriceps…

Q: Task 3: The sketched overhead crane carries the effective force F1 = 60 KN and the balancing load F2…

A: provide the specific functionality of the PLC program in the image without more contex

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: Given Length of the ladder = 10 m Weight of the ladder = 350 N Ladder angle = 30o Weight of the…

Q: A uniform 200-lb boom that is 24 ft long is supported by a cable as shown in the accompanying…

A:

Q: A horizontally positioned door weighing 1200 N is held in place by hinges centered at points A and B…

A: Given: The weight of door, W = -1200k

Q: Figure below shows a system with two weights on a rotating shaft. For the given data below,…

A: Balancing : There are inertial forces present in machine component associated with moving parts .…

Q: 2.18 A 200# stone is being lifted off the ground by a lev- ering bar. Determine the push P required…

A:

Q: Part (a) Choose the correct free-body diagram for the door. F, Mg Mg F. F. F Mg F Mg F Part (b)…

A: Given data Mass of the door = M = 33 kg Height of the door = h =  2.2 m       [ Note : According to…

Q: a. Compare the size of the force placed on your bicep muscle to the force of the 20 lb dumbbell…

A: The weight of the dumbbell is given by, Consider some essential dimensions.

Q: Consider the following hanging mass system for the following problems. Before answering the…

A:

Q: 1. Calculate the loads in bicep muscle and upper arm bone. Indicate if the muscle and bone are in…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.