A hydraulic crane of total mass (including the mass of the boom) 5300kg supports a load of 800kg. The boom mass 500kg is 7m long and makes an angle of 50 degrees with the horizontal. The boom's center of the boom length. Also assume that the center of mass of the crane excluding the boom acts at the middle of the outrigger jacks that are 4m apart. Draw the FBD of the crane and boom. Find the reaction force at the rear outrigger jack (Nr) and at the front (Nf) for the system to be in equilibrium. Assume the ground is friction less. 7m

A hydraulic crane of total mass (including the mass of the boom) 5300kg supports a load of 800kg. The boom mass 500kg is 7m long and makes an angle of 50 degrees with the horizontal. The boom's center of the boom length. Also assume that the center of mass of the crane excluding the boom acts at the middle of the outrigger jacks that are 4m apart. Draw the FBD of the crane and boom. Find the reaction force at the rear outrigger jack (Nr) and at the front (Nf) for the system to be in equilibrium. Assume the ground is friction less. 7m

Name: A hydraulic crane of total mass (including the mass of the boom) 5300
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A hydraulic crane of total mass (including the mass of the boom) 5300kgsupports a load of 800kg. The boom mass 500kg is 7m long and makes an angleof 50 degrees with the horizontal. The boom's center of the boom length. Alsoassume that the center of

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The scow is 40 ft long, 20 ft wide, and 8 ft deep. It has a draft of 5 ft when floating in an upright position. The center of gravity of the scow is on the axis of symmetry, 1 ft above the water surface. Compute (a)the initial metacentric height and (b) the righting moment in freshwater when the angle of the heel is 10° *NOTE: use Fb=W to solve for the weight
Draw the free body diagram for this problem: The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom.
A beam rests on a fulcrum, 1.2 m from one end. A weight of 350 kg is suspended from this end causing the beam to balance. If the weight of 350 kg is suspended on the opposite end of the beam, it is necessary to suspend a 1000 kg weight on the first end in order to effect an even balance. Find the lenght of the beam
below. Its dimensions are 1 m x 1 m. What moment is needed to start the trap door lifting? Assume the force of gravity is 9.81 N/kg. Hinge
The structure shown below is a simplified tower crane. It carries a shipping crate suspended from B that has a weight of 116 kN . The main jib DCB (in green) has a weight of 17 kN concentrated in the center of the beam. This is pinned to the main body at D and is supported by a cable that is routed through pulleys at F and G and is attached to a concrete counterweight J. The main body AEFG (in yellow) is fixed to the ground at A. Various geometry: h1= 26.5 m h2= 3.9 m h3= 5.1 m l1= 12.8 m l2= 17 m l3= 4.3 mm θ= 57.6 degrees Assumptions : The main body AEFG can be considered massless. The cable CFGJ is massless. The pulleys at F and G can be considered massless, frictionless, and of negligible diameter. All bodies are considered rigid. Questions: Determine the weight of counterweight J in order for the main jib DCB to be horizontal. Determine the magnitude of the x and y components of force at pin D. Determine the reactions at fixed support A.
A person of mass 73 kg is standing on a 25 kg horizontal board of uniform density that is 5.0 m long. The supported by vertical pillars at cach nd. The left pillar exerts 900 N on the board. A. What is the force by the pillar on right on the board? Show your wok. B. How far from the left end is the person standing? Show all work including a force diagram.
A semicircular floodgate is 4.0 m long and 3.0 m radius. It is articulated at its lower point and has a latch at its top point. disregarding the weight of the gate, what will be the reaction forces on the latch and joint? NA
A 50 kg pole extends up a wall, making a 60° angle with the wall. The pole is supported by acable attached 3/4 of the way along the pole. This support cable is perpendicular to the wall.A 10 kg sign hangs from the end of the pole. The pole’s center of mass is 1/3 of the way fromthe wall to the end of the pole. (a) What is the tension in the cable?(b) What are the x and y components of the force the wall exerts on the pole?You must include an extended free body diagram showing all forces acting on the pole. Labelthe location on the pole you will use a reference for measuring distances (the “axis of rotation”) at the point where the pole touches the wall. Thank you!
Pivot A constant density bar with mass m and length Lis held in place as shown. Use the usual x,y,z coordinates for the following questions. Celling Cable 12. Measuring from the pivot, in the space below draw the torque-pic for the weight force exerted on the bar. Be sure your torque-pic includes both an expression for r in terms of L and also the value for the angle between r and weight force. Bar 350 Length = L
Make a free-body diagram of the boom. The boom attaches to the building at dot A. The center of gravity of the boom is indicated by dot B. The guy wire attaches to the boom and holds the load at dot C.
wor The uniform boom shown below weighs 5000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at 'A' act along the boom? A 45° 2000 N
Draw the free-body diagram for the following problem. The crane and boom shown.