Name3a. Calculate the average dead load per square foot for the construction assembly shown.Built up pitch and gravel roofing3/4" plywood sheathing2x10 joists, 16" 0.c.actual dimensions: 1-1/2" x 9-1/4"lighting and mechanical (not shown)1/2" painted drywall ceiling6 #/ft²1.5 #/ft²32 #/ft³1 #/ft²2 #/ft²

Answered: Image /qna-images/answer/50abedeb-0ffb-4cee-a9e5-99ee0e7f150c.jpg

ame 3a. Calculate the average dead load per square foot for the construction assembly shown. Built up pitch and gravel roofing 3/4" plywood sheathing 2x10 joists, 16" o.c. actual dimensions: 1-1/2" x 9-1/4" lighting and mechanical (not shown) 1/2" painted drywall ceiling 6 #/ft² 1.5 #/ft² 32 #/ft3 1 #/ft² 2 #/ft²

ame 3a. Calculate the average dead load per square foot for the construction assembly shown. Built up pitch and gravel roofing 3/4" plywood sheathing 2x10 joists, 16" o.c. actual dimensions: 1-1/2" x 9-1/4" lighting and mechanical (not shown) 1/2" painted drywall ceiling 6 #/ft² 1.5 #/ft² 32 #/ft3 1 #/ft² 2 #/ft²

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter32: Drawing Framing Plans

Section: Chapter Questions

Problem 32.1Q: What are the two major methods of determining lateral loads?

See similar textbooks

Similar questions

Prepare the details estimate for the following 2 roomed building epare BOG the foilowing WI w1 D2 3500 mm x 3400 mm 4000 mm x 3400 mm W1 D1 D1 -Door 1 1100mmx 2100mm D2 -Door 2 1000mmx 2100mm W1-Window 1 1200mmx 1200mm Roof height: 2.80m Consider bearing for lintel as RCC roof 170mm thick Lintel 0.15m thick 300mm 1 300 mm 750 mm 1000 mmm- 1200 mm ww 00s ww 00s 200 mm ww 00s
4.22 Give the time effect factor for the following load combinations: a. 1.2D + 1.6S + L b. 1.2D + W + L + 0.5S c. 1.2D+ 1.6L + 0.5S with L from occupancy d. 1.2D+ 1.6L, + L e. 1.4D 4.23 What reference design values for wood, if any, are not subject to adjustment for duration of loading (ASD)? For time effect (LRFD)?
concrete floor analysis
The total length of exterior walls of a residential building is 650 lf. The 8-foot long 2x4 studs are spaced 16 in. OC or less. The drawing of the building shows there are 20 corners requiring three studs. Studs are installed on single 2x4 bottom sill plates and capped by double 2x4 top plates for the entire length of the walls. Both bottom and top plates are 16-ftlong each. Prepare a list of materials for the wall studs, corner studs, sill plates, and top plates. For each of the materials, show the nominal dimension, number of pieces of each length, the length ofa lumber, and the total linear feet. Estimate the total direct cost and cost per linear foot of wall for furnishing and installing the studs and plates. Assume $0.75/bf for lumber, $30.00/hour carpenters, and $24.00/hr for laborers. Use the average value in Table 12.10 for the labor-hours
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.
anwser #2, please
anwser #1 please will rate
Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.60 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% in pieces of CHB c) How much mortar or grout is required in CHB laying? In cubic meter d) How many bags of cement is needed if Class B 1:3 Mixture is required? WF-3% No. of 40kg bags e) Find the volume required for the fine aggregate if WF sand = 15%, in cubic meters f) How many pieces of 10mm diameter x 6 meters long rebar must be ordered? In pieces g) What will be the total mass of the reinforcing steel bars, in kilogram? In kilograms Metal anchors to be enbedded in mortar DOOR- FRAMES
question is attached. thank you!
a) 5309 lbs b) 2428 lbs c) 867 lbs d) 1619 lbs
Urgent please
Determine the purchase quantity and number of board feet of 2 × 12 joist needed for the floor in the figure below. The joists are spaced 16 inches on center. Be sure to include the headers. DOUBLE JOIST UNDER WALL 24' 8' 10' 2x12 HEADER 22¹-8" -4x4 POST DOUBLE JOIST 10'-7" 2x12 HEADER 2x12 @ 16" O.C. 36' 2@2x12 GIRDER DOUBLE JOIST UNDER WALL 10'-9" 13'-4" DOUBLE JOIST- UNDER WALL 2@2x12 GIRDER 4x4 POST 2x12 HEADER 10¹-8" 2x2 HEADER 10' 12° 34' 12'