Given the following rectangular (35 ft x 45 ft) two-story warehouse and loading shown, determine the effective weight at the roof and first floor and the total weight of the structure 2 ft Roof 14 ft 1st level 16 ft Base ▪ Roof DL = 55 psf Floor DL = 65 psf ■ ■ ■ ■ >k Wall DL = 35 psf Floor LL = 250 psf (storage) SL = 50 psf WONG effective, ro effective, 1 ||| W₂ W₁

Given the following rectangular (35 ft x 45 ft) two-story warehouse and loading shown, determine the effective weight at the roof and first floor and the total weight of the structure 2 ft Roof 14 ft 1st level 16 ft Base ▪ Roof DL = 55 psf Floor DL = 65 psf ■ ■ ■ ■ >k Wall DL = 35 psf Floor LL = 250 psf (storage) SL = 50 psf WONG effective, ro effective, 1 ||| W₂ W₁

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter16: Budget Estimating

Section: Chapter Questions

Problem 4RQ: Prepare a typical bay estimate based on the following information: a. Bay size of 350 feet and a...

See similar textbooks

Similar questions

Q#2: (a). What is consolidation? Explain the concept of NCR and OCR with examples [in your own words]
Listen What should you enter for the Total HAWB on the Consolidation Manifest? 2 34 14 20
tez fer 3500 psi 15,5" Grade 6o steel 448 O 0 o o I 2,5" NWC. $ Mn= ? 12" Tied stirrups.
You are a structural Engineer who works in Dar Al Handasah company. Your ene-up-direct manager has called for a meeting and providedyou with the below schematic design of a concrete beam that might þe implemented at one of the sites. You were requested to calculate the following: (make 15 KN bold) 40 KN 15 KN 20 KN 45 30 KN 40 KN 16 20 Figure 1: Concrete Beam 1. Find the equivalet forces of the disturbedloads. 2. Sketch the beamshowingwith all the applied forces (reaction and equivalent forces) and allocat theminto thetheir suitable locationsproperpoints. 3. Apply the momentequations in the equilibrium state to find the value ofthe reaction forces at points A and B. 4. Ifthe given beamin Figure 1 compressedehrank to be 19.98 meter where the originaltempreture was atthe giventemperature T1=200 K, find the temperature (T2) afterthe compressionelminking.
b) Classify each work breakdown structure for the proposed two-storey according to the three (3) construction stages? FABRICA TION FABRICATION OF OF FORMWORKS (REINFORCING BARS SEEL TRUSES ABRICATION OF BUILDING PERMIT (CONSTRUCTION OF TEMPORARY FACILITIES (CLEARING AND GRÜBBING DEWATERING (IF ANY) PLACEMENT OF REINFORCING BARS OF FOOTING FOUNDATION MOBILIZATION STAKE OUT EXCAVATION SOL POŠONING INSTALLATION OF REINFORCING BARS OF CONCRETE HOLLOW BLOCKS (CHB NSTALLATON CE STARTER BARS OF COLUMNS ----- SOIL POISONING OF STRUCTURAL BACKFILL COMPACTION OF STRUCTURAL BACKFILL CONCRETE, POURING OF FOOTING AND TE BEAMS PROVISION OF FORMWORKS FOR TE BEAMS INSTALLATION OF REINFORCING BARS FOR TIE BEAMS ACKFILL INSTALLATION OF REINFORCING B ARS FOR GIRDER AND BEAMS INSTALLA IION OF ELECTRICAL CONDUI TS INSIDE THE COLUMNS (IF ANY) L------- ------ INSTALLATION OF SHRINKAGE AND TEMPERATURE REBARS CF SLAB-ON-GRADE PREPARATION OF FORMWORKS FOR COLUMNS POURING OF CONCRETE AT MID OF COLUMN HEIGHT…
Where would you put major building (separation) joints in the combined buildings shown below. A▾ B I EE > 32 3 EE ≡≡
Define The shape of the loaded area
Please fast answer
Home-Work 1 Q1:- what is the function of the Substructure and Superstructure in the Building. Q2:- for the given building shown below determine the Substructure and Superstructure of the Building Roof Second Floor Ground Floor
How is the float useful for the contractor?
Calculate the Load distribution of slabs to beams 2, C and D using 10kPa load multiplied by the tributary width. Yellow represents columns and purple represents beams.
Calculate the Load distribution of slabs to beams 2, C and D using 10kPa load multiplied by the tributary width. White represents columns. Blue represents beams.