ame 3a. Calculate the average dead load per square foot for the construction assembly shown. Built up pitch and gravel roofing 3/4" plywood sheathing 2x10 joists, 16" o.c. actual dimensions: 1-1/2" x 9-1/4" lighting and mechanical (not shown) 1/2" painted drywall ceiling 6 #/ft² 1.5 #/ft² 32 #/ft3 1 #/ft² 2 #/ft²

Q: a. Calculate the average weight of the floor, including the weight of slab, beams and non-structural…

A: Given: Density of concrete = 150 pcf Beam size = 7' wide x 20'' deep Slab thickness = 14'' thick To…

Q: A living room measuring 7m x 4m uses 2"x2" ceiling joists The total board foot of ceiling joists…

A: To calculate the number of 2"x2"x12' ceiling joists required to cover the entire room, we need to…

Q: Can you please do the calculations for the partition loads as well. Thanks

A: where,  A=40 ft  B=19 ft  C=9ftThe given building is a school located in Los Angeles, CATo…

Q: • Live load = 40 psf • Decking = 5 psf • Beams = 5 plf . Girder = 20 plf . Concrete density = 150…

A: Tributary area of Post A

Q: Can you please answer the question in the picture and show all of the work, please

A:

Q: (2) 27"/ 6" TE #4 4 #9 (1) d = ? (2) C= ? 39 Jove d-c fé= 3 ksi Grade 60 steel NWC. & Mn = ? #4 tied…

A: Given: fc = 3 ksi fy = 60 ksi Cover = 1.5 inch

Q: Using the same framing plan as the previous prompts, find the total point load on the column labeled…

A:

Q: 9.17 An 8 x 8 S4S first-floor column supports a load of P₁ = 20 k from roof and floors above and an…

A: Given column section - 8×8 S4S Doughlas FIR No.1 Column  P1 =20 k  P2 = 12 k  E=1600 ksi  Fc= 1000…

Q: The top part of the table shows the computation for the corner columns at grid point A-1. Fill out…

A:

Q: 1. Determine the maximum allowable load for each of the following 6x6 columns, if the unbraced…

A: Unbraced length (L) = 9 ft or 108 in Pin connections

Q: 4.22 Give the time effect factor À for the following load combinations: a. 1.2D + 1.6S + L b. 1.2D +…

A: NOTE : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: Figures below show the typical floor framing plan and sections of a three-story reinforced concrete…

A: Given data:- Weight of concrete, w=150 pcf Characteristic strength of concrete, f'c=4000 psi Yield…

Q: Complete Loading calculation (floors and roof dead load calculations including estimated loads of…

A: where, A=40 ftB=19 ftC=9ftThe given building is a school located in Los Angeles, CATo determine:Dead…

Q: Which of the following represents the effective slab width for the composite beam (Beam 1)…

A: For the beam (beam 1) highlighted in the figure, the span of the slab it needs to support is,…

Q: . b. 15" Calculate the weight of a 1'-0" length of the following materials. 3-1/8" 15" 12",3" 4" 40"…

A: To find the weight of one foot length of the given materials. L= 12”D1, Density of Glued-laminated…

Q: 4.4 Refer to the framing span diagrams from Architects' Studio Companion and answer the following…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: CHAPTER 2 ASSIGNMENT: Use the NSCP 2010 for the following problem sets using the framing plan shown:…

A: As per the policy, the first three subparts are solved. post the remaining subparts as a separate…

Q: QUESTION 5 The structural timber built-up section is fabricated as shown below. Calculate radius of…

A:

Q: please answe this, i will give you upvote

A:

Q: solid timber columns at 2.5m height as part A client requests to install a series of five of his…

A: Timber design is normally used for designing a structure that forms a building that using primarily…

Q: Determine the required spacing of #3 stirrups (Grade 40) along the length of a 5000 psi, 35-ft long…

A: Compressive strength of concrete (fc') = 5000 psiYield strenght of steel (fy) = 60000 psiWidth of…

Q: Please show all of your work, thank you for your help!

A:

Q: 3) What is the allowable load capacity, P., for a 4 in. x 6 in. nominal (3.5 in. x 5.5 in.) sawn…

A: Data Given: Dimensions = 4" × 6"Fc = 1300 psiCD = 0.9FCE = 774 psi Asked: Allowable load capacity…

Q: ELOrED HAPTERG BEAHNG WALL BEAM COLIMN FFAMING PLAN -BEAM -COLUMNS -DEAHINGT WALL FRONT BLBVATION…

A: Live snow load = 25 psf Dead load due to roof and sheathing= 14 psf Total= 25+14= 39 psf Total span…

Masonry wall construction

Masonry walls of various sorts are utilized in building construction. Masonry walls are the most enduring feature of any structure or building. It separates a structure from the outside world. In masonry construction, the common masonry materials used are building stone, brick, cast stone, glass block, and concrete block. Masonry construction is a type of construction that has the highest durability.