CHAPTER 2 ASSIGNMENT: Use the NSCP 2010 for the following problem sets using the framing plan shown: SITUATION: The second floor of a library has any area that can be used for stacks. Assume that there will be a steel channel ceiling system (0.10kPa) and asphalt tile on the floors. The floors are 150mm reinforced concrete. Allowance should be provided for mechanical ducts. Determine the: a. floor dead load in kPa. b. live load in kPa to be applied to Column C3 c. reduced floor live load in kPa, if any B Basic building layout 4 at 12m 48m

CHAPTER 2 ASSIGNMENT: Use the NSCP 2010 for the following problem sets using the framing plan shown: SITUATION: The second floor of a library has any area that can be used for stacks. Assume that there will be a steel channel ceiling system (0.10kPa) and asphalt tile on the floors. The floors are 150mm reinforced concrete. Allowance should be provided for mechanical ducts. Determine the: a. floor dead load in kPa. b. live load in kPa to be applied to Column C3 c. reduced floor live load in kPa, if any B Basic building layout 4 at 12m 48m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3: Make a comparison between the types of brick walls shown in the pictures. A В C D
question is attached. thank you!
3. Design a one-way floor simply supported slab (16ft x 35 ft) in size to carry a uniform live load of 500 psf. Given f=4000 psi and fy=50000 psi. Use the ACI 318 code. Draw the reinforcement detail also.
Submit your question to our 24/7 subject matter experts with Masters and PhDs and get a solution in as fast as 30 minutes* Provide clear and step by step solution with illustration Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.
15. Calculate the fire resistance of a configuration of 4 wythes (monolithic slabs) of normal weight concrete each 2 inches thick. Use a conservative approach
While inspecting the roof sheathing, you see a continuous void parallel to the crest. Which of the following statements accurately describes the function of this space? A. Resistance to wind B. Ventilation D. Diversion of water
What is the clear wall R-value of a typical 2X6 stud wall assembly? Assume the following: (1)cavity has dense pack cellulose at R 22 (2)there are 1 percent air gaps in the cavity insulation with a nominal R value of 1 for the air gap (3)the framing factor is 22 percent with an R value of 1.25/inch (4) There is 1 inch of continuous XPS (R5/inch) on the exterior (5)Assume the air films, sheathing, facade, and wallboard add an additional 1.5 R value to the wall. Hint: draw this out. Answer:
Before any system of precast concrete flooring is put in consideration, several factors must be put into account; mention some of these factors
Describe the core barrels as single wall or double wall.
(3) H 22" IN_ 1:3|2|2|2|3| 4 #8 (b) Check if the #8 bars As, reg 2.85 in ² #4 at 8" 0.c. fé=4.000 psi Grade 60 steel Light weight concrete No-Coating. (a) check if 4 #8 Bars fit the beam. are sufficently anchored (I
A floor plan shown below is subjected to an imposed load of 2.5 kN/m². and a floor finish load of 1.5 kN/m². Assuming the size of all the beams as (300mmx550mm), Grade of concrete as C25/30, steel strength as 500 N/mm², XC2 exposure condition, unit weight of concrete as 25 kN/m³ and simply supported condition. 2) Calculate the design loads for beams B1 - D1 and B2 - D2.
Please write clearly