A B) 24'-0" 12'-0* 12'-0" to (2 CVOID 16'-0" 8'-0" The floor plan above, shows steel beams which support an 8" thk RC slab with a terrazzo floor finish. The terrazzo floor finish imposes a uniformly distributed load of 20 psf, while the live load over the entire slabbed area, can be taken as 50 psf. The unit weight of concrete is 150 pcf and the self-weight of the steel beams can be ignored. a) Show the tributary areas over all the beams on a plan drawing. b) Calculate the total factored loads on the beam shown on gridline '2' and draw its loading diagram, showing the total factored loads as well as its factored reactions. to 0-9 0-,

A B) 24'-0" 12'-0* 12'-0" to (2 CVOID 16'-0" 8'-0" The floor plan above, shows steel beams which support an 8" thk RC slab with a terrazzo floor finish. The terrazzo floor finish imposes a uniformly distributed load of 20 psf, while the live load over the entire slabbed area, can be taken as 50 psf. The unit weight of concrete is 150 pcf and the self-weight of the steel beams can be ignored. a) Show the tributary areas over all the beams on a plan drawing. b) Calculate the total factored loads on the beam shown on gridline '2' and draw its loading diagram, showing the total factored loads as well as its factored reactions. to 0-9 0-,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam 250 mm wide, 500 mm deep is reinforced at thebottom with 4-20-mm-diameter bars and at the top with 2-16-mmbars. Concrete cover to bar centroid at the top is 80 mm and at thebottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yieldstrength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the limiting tensile steel ratio for a tension controlledcondition in positive or negative bending with the given materialstrengths. ρt = [r] in 5 decimal places (ex. 0.00001)
Q#1: Modify the reinforcement steel of the concrete sections shown below considering the seismic detailing.
Given the section and plan view of the structural elements (Foundation and Column), estimate the concrete material quantities to be used in construction. There are sixteen (16) - C3F2 in the entire structure. Consider only from the foundation base up to the Natural Ground Level (NGL). The concrete is to have a minimum compressive strength of 3500 psi (24 Mpa).
Homework3 A simply supported concrete slab given the section depth is 100mm, concrete grade is C30 and reinforcement grade is HPB300. The span of slab is 19=2.38m. The live load applied on the slab is ge=2kN/m2 and the dead load include: 1. Its self-weight given concrete (include reinforcement) bulk density is 28kN/m3 2. Terrazzo floor and fine stone cushion layer is 30mm(bulk density is 22kN/m) and the ceiling plaster mortar is 12mm(bulk density 17kN/m²).
A simply supported beam 3e0 mm wide, 500 mm deep and spans 5.2 m supports a service super imposed dead load of 7 kN/m and service live load of 6 kN/m. Concrete strength f's - 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
B) For reinforced concrete lining, the transverse reinforcement is two times the longitudinal reinforcement.O FalseO True
1.22 Calculate the design moment strength of the precast concrete section shown in Fig. 3.39 using f = 4 ksi and f, = 60ksi. 6.3" + Canon 14" 5#9 20" 19" 2.5" 2.5"
4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
10. A simply supported beam 300 mm wide, 500 mm deep and spans 5.0 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"