Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.60 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% in pieces of CHB c) How much mortar or grout is required in CHB laying? In cubic meter d) How many bags of cement is needed if Class B 1:3 Mixture is required? WF=3% No. of 40kg bags e) Find the volume required for the fine aggregate if WF sand = 15%, in cubic meters f) How many pieces of 10mm diameter x 6 meters long rebar must be ordered? In pieces g) What will be the total mass of the reinforcing steel bars, in kilogram? In kilograms

Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters excluding the doorway, is reinforced with 10mm diameter steel bars at every 3 layers horizontally and 0.60 meters on center spacing for vertical bars. a) What is the total area of the CHB installed or laid? A=? in square meters b) How many blocks are required? N=? pieces Provide Wastage Factor = 3% in pieces of CHB c) How much mortar or grout is required in CHB laying? In cubic meter d) How many bags of cement is needed if Class B 1:3 Mixture is required? WF=3% No. of 40kg bags e) Find the volume required for the fine aggregate if WF sand = 15%, in cubic meters f) How many pieces of 10mm diameter x 6 meters long rebar must be ordered? In pieces g) What will be the total mass of the reinforcing steel bars, in kilogram? In kilograms

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the minimum area (Asmin) for the following concrete beam: b = 10 in, d = 17 in, fy = 60000 psi, and f'c = 5000 psiNote: This is an ACI code check and not required As determined by the moment. Answer in inches^2 and to 3 decimal places. Type your answer...
The two pieces of wood, 2.94in. by 4.76 in., are glued together along the 48ᴼjoint. Determine the maximum safe axial load P (in lb) that can be applied if the shear stress in the glue is limited to 275 psi. Round off the final answer to three decimal places.
As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B 30'-0"- B2 -EQ.- EQ. -EQ. SEC 1 -40'-0" IS B1 B3 B3 B1 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in². EQ. 40'-0" B EQ. North
:In the given composite structural section determine the quantities placedinthe table below. Answers placed are final and NO ERASURES are to be made. PLACE YOUR ANSWERS HERE. 10 " Ix = 1" Iy= 4"X6"X %" rx = ry= 12" 4"X 8"X 1" 2"
Two wooden planks, each 12 mm thick and 225 mm wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 20 MPa, determine the magnitude P of that axial load which will cause the joint to fail. provide your answer in kN with precision to two decimal points. 16 mm 16 mm 25 mm 50 mm 225 mm P P 50 mm 25 mm Answer:
C O N S T R U C T I O N M A T E R I A L S A N D T E S T I N G Discuss at least five lumber defects.
Show 5 failures. Show step by step solution. Steel Type: Cross section flat bar PL 12.7 x 165 with an area of 2095.5 mm2 Textbook reference Handbook of steel construction.
C30 concrete, S420 Steel, h=600mm, b=800mm, hf=100mm, bw=300mm, d'=40mm, steel rebars top and bottom = 5Φ20
4. According to ASTM A615, what are the minimum yield stress, tensile stress, and elongation for a No. 6 Grade 100 bar?
Question 4 A 6 KN force is applied at the free end of a wood (E = 12GPa) beam with dimensions given in Fig. Q4. Neglecting the effect of fillets and stress concentration, determine (a) the maximum compressive stress and its location at section A-A; (b) the maximum shearing stress and its location at section A-A; (c) the deflection at section A-A. 6 kN 300 mm 400 mm ΤΑ 叶 ¡A Fig. Q4 96 mm -- 12 mm 12 mm 48 mm
Q.5: Write in detail about different methods of pre-stressing. Also write about the erection methods for pre-cast units in detail.
What is the maximum area of reinforcements (mm?) of the concrete beam if the specified compressive strength and the steel yield strength are 27.1 MPa and 389 MPa respectively? The concrete beam has a width of 307 mm and an effective depth of 561 mm. Note: Round off only on your final answers. (2 decimal places, No need to type the units)