Zhpe Outine leceSelect834 Anange OickCreate wnd ShaneAdobe POAdite ASydesO upe iectstereDingteting1. (a) A tension test was performed on a magnesium alloyspecimen having a diameter 12 mm and gauge 50 mm. Theresulting stress-strain diagram is shown figure. Determinethe approximate modulus of elastic and the yield strengthof the alloy using the 0.2% offset method.(MPa)280245(b) A tension test was performed on a magnesiumspecimen having a diameter 12 mm and gauge 1ength of50 mm. The resulting stress-strain diagram is shown inthe figure. If the specimen is stressed to 210 MPa andunloaded, determine the permanent elongation of the210175140specimen1057035(me0.002 0.004 0.0060.008 0.010ANates

given- a stress-strain curve obtained by performing tension test on magnesium alloy. required- to…

(a) A tension test was performed on a magnesium alloy specimen having a diameter 12 mm and gauge 50 mm. The resulting stress-strain diagram is shown figure. Determine the approximate modulus of elastic and the yield strength of the alloy using the 0.2% offset method.

(a) A tension test was performed on a magnesium alloy specimen having a diameter 12 mm and gauge 50 mm. The resulting stress-strain diagram is shown figure. Determine the approximate modulus of elastic and the yield strength of the alloy using the 0.2% offset method.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
(b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm and a gauge length of 25 mm. When a load of 4500 N is applied during the test, the gauge length of the specimen extends to 25.02 mm. If the Young's Modulus of the steel is 199 GPa, calculate the diameter of the tensile test specimen used. 4
a. Which of the following gives the approximate modulus elasticity of the The stress-strain diagram for a steel alloy having an original diam. of 12 mm and a material? gauge length of 50 mm is given in the figure. b. Which of the following gives the load on the specimen that causes yielding? c. Which of the following gives the ultimate load the specimen will (8) MPa ultimate strength- 80 support? 70 60 repture' strength yäerd põint- 50+ 40 propórtional limit 30 20+ 10+ 0 .0005 .001.0015 .002 .0025 .003 .0035 E(mm/mm)
A 7075-T651 alloy is used in a structural component in an airplane. The component must not fail when subjected to a stress of 250 MPa. Several surface flaws have been detected on the component. What is the largest (deepest) surface flaw that could be permitted with the 250 MPa maximum stress? Use data from Table 1 and assume this component geometry and loading condition result in a Y value of 1.25. Yield Strength KI Material MPa ksi MPa√m ksiVin. Metals Aluminum alloy (7075-T651) 495 72 24 22
Urgent. a = 10 , b = 7 solve this question about those information.
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the brass. Steel Brass Copper Est = 200 GPa 12(10-)/°C apr Ebr Ecu 17(10-)/°C 120 GPa 100 GPa %3D ast = 21(10-6)/°C acu Acu = 515 mm? |Ast 200 mm2 Abr = 450 mm2 300 mm -200 mm 100 mm O -0.0109mm O 0.0241mm O -0.0241mm O 0.0109mm oooO
Solve Subparts b, c and d early I upvote. But only Correctly solution provided.
Task (3) you are asked to perform tensile test on specimens of two different materials (A and B) and you obtained the stress-strain diagram of the two specimens as shown in Figure 2: 400 350 300 250 Material A 200 150 100 50 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 Strain (mm/mm) 50 Material B 30 20 10 0.02 0.04 0.06 0.08 0.1 Strain (mm/mm) Figure 2: Tensile Test Analysis Stress (MPa) Stress (MPa)
Can you answer part i please
7)
During a tensile test on a specimen of steel the following data was recorded diameter of the specimen is 6.6mm,gage length 5mm,elongation of a load of 6.0KN is 0.043mm.load at yield point is 9.7KN at failure is 14.2KN ,reduction of the area is 45 percent. Calculate Young's modulus of elasticity, the yield stress and the ultimate stress