PROBLEM 3-18 GIVEN: A tension test was performed on a magnesium alloy specimen having a diameter 0.5 in. and gage length of 2 in. The resulting stress-strain diagram is shown in the figure. or (ksi) 40) 20 25 15 0.008 REQUIRED: If the specimen is stressed to 30 ksi and unloaded, determine the permanent elongation of the specimen.

PROBLEM 3-18 GIVEN: A tension test was performed on a magnesium alloy specimen having a diameter 0.5 in. and gage length of 2 in. The resulting stress-strain diagram is shown in the figure. or (ksi) 40) 20 25 15 0.008 REQUIRED: If the specimen is stressed to 30 ksi and unloaded, determine the permanent elongation of the specimen.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Engineering strain of a mild steel sample is recorded as 0.100%. The true strain is 1. 2. 3. 4. 0.010% 0.055% 0.099% 0.101%
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is oal = -90 MPa and the initial temperature 20°C. 2) The final length of the aluminium member. Aluminum A=1800mm? E=73GPA Bronze A=1500mm2 E=105GPA a=23.2x10-6/°C a=21.6x10-6/°C Gap=0.5mm 0.35m 0.45m
At a temperature of 27.89 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 126.64°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 320.36 mm and M = 231 mm. Round off the final answer to four decimal places. d ... M A B Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/C A = 800 mm² E = 190 GPa %3D a = 17.3 × 10-6/°C
A specimen of metal of original length 80mm and original diameter 21mm was subjected to tensile a test. The load and extension at the limit of proportionality were found to be 105,000N and 0.082mm. The yield point was at a load of 112,00ON. The maximum load before the material failed was 199,000N. The final length at failure was 91mm. Calculate: i. the stress at the limit of proportionality i. the yield stress iii. the ultimate tensile stress iv. the value of Young's Modulus V. the strain at failure
Nilo
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
The following information about the o-e curve is given for a steel alloy. E = 0.001527 at o = 300 MPa and ɛ = 0.003054 for o = 600 MPa. (a) Draw the stress-strain diagram and calculate the E for this alloy.
At an axial load of 20 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 3.3 mm while the bar width contracts 0.21 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
A steel plate used for polymer forming is to be bent into a circular shape having an inside radius of 10 m. What maximum thickness can be used for the plate if the normal stress is not to exceed 267 MPa? Assume that the modulus of elasticity for the steel is 201 GPa.
An aluminium specimen with an initial gauge diameter d, = 10 mm and gauge length, 1, = 100 mm is %3D subjected to tension test. A tensile force P= 50 kN is applied at the ends of the specimen as shown, resulting in an elongation of 1 mm in gauge length. The Poisson's ratio (µ) of the specimen is Take shear modulus of material, G = 25 GPa. Consider engineering stress-strain conditions. P