An aluminium specimen with an initial gauge diameter do = 10 mm and gauge length, 1 = 100 mm is subjected to tension test. A tensile force P= 50 kN is applied at the ends of the specimen as shown, resulting in an elongation of 1 mm in gauge length. The Poisson's ratio (u) of the specimen is _ Take shear modulus of material, G = 25 GPa. Consider engineering stress-strain conditions. †P

An aluminium specimen with an initial gauge diameter do = 10 mm and gauge length, 1 = 100 mm is subjected to tension test. A tensile force P= 50 kN is applied at the ends of the specimen as shown, resulting in an elongation of 1 mm in gauge length. The Poisson's ratio (u) of the specimen is _ Take shear modulus of material, G = 25 GPa. Consider engineering stress-strain conditions. †P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x
Theory of failure.
For a point on a steel specimen, the principal stresses are known to be 01 = 360 MPa and O2 = 60 MPa. Calculate the minimum yield stress of the material according to the Tresca criterion. Give your answer in MPa to 3 significant figures.
Q: A rectangular short tied column (900*500 mm) subjected to axial ultimate load of 4800 kN which produce ultimate moment about strong and weak axes of (1000 and 430 kN.m), respectively. Use fc'=28MPA, fy=400MPa and d=65 mm. Required: Design of the column.
Solve it correctly please.
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
At a temperature of 28.42 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 137.38°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 339.61 mm and M=240 mm. Round off the final answer to four decimal places. d ... В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6°C
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
A prismatic bar has a cross-section of 25 mm x 50 mm and a length of 2000 mm. Under an axial load of 100 kN, the measured elongation of the bar is 2 mm. The tensile stress and % strain in the bar are?
A single zinc crystal is loaded in tension with the normal to its slip plane at 60° to the tensile axis and the slip direction at 40° to the tensile axis. a) Calculate the resolved shear stress when a tensile stress of0.69 MPa is applied. b) What tensile stress is necessary to reach the critical resolved shear stress of 0.94 MPa?
At an axial load of 20 kN, a 45-mm-wide by 10-mm-thick polyimide polymer bar elongates 3.3 mm while the bar width contracts 0.21 mm. The bar is 240 mm long. At the 20-kN load, the stress in the polymer bar is less than its proportional limit. Determine (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar thickness. Answers: (a) E= (b) v = (c) Athickness= i i i GPa mm
Consider a cylindrical specimen of a steel alloy (Please see the figure) 0.33 in. in diameter and 3.15 inches long that is pulled in tension. given:-Elongation is 0.018 in-Tensile stress = 200 ksi -Tensile strain = 6.83*10^-3 -Ultimate stress = 281.82 ksi -Ultimate strain = 0.05solve: Fracture point (stress and strain values)