If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of spring B and having an equal number of active coils and same wire diameter are subjected to a same axial load of W, then the ratio of deflection in spring A to B. 1. 8 1 4 3.2 4.8 2. strength-of-materials springs

If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of spring B and having an equal number of active coils and same wire diameter are subjected to a same axial load of W, then the ratio of deflection in spring A to B. 1. 8 1 4 3.2 4.8 2. strength-of-materials springs

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A circular flat plate of diameter 120 mm and thickness 10 mm is constructed from steel with E = 208 GN/m² and v=0.3. The plate is subjected to a uniform pressure of 5 MN/m² on one side only. If the plate is clamped at the edges determine: (a) the maximum deflection; (b) the position and magnitude of the maximum radial stress.
78.75 мра 33.61 MPa 22.11 MPG Determine @ Omax Omin Tmax (@s, @p) sketch the result JLULL e pain wel, w un pipar places an B , (b) the stress components exerted on the element obtained by rotating the given element clockwise through 30°. Sketch the result
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 400 N is applied to it, determine the change in its length and the change in its diameter. E = 3.20 GPa, v = 0.4. %3D 400 N 400 N 200 mm
Consider the timber beam shown below. The beam is made out of southern yellow pine, with an allowable bending stress of ?all= 2700 psi. The modulus of elasticity is E = 2,400 ksi. The maximum allowable deflection in the beam is 0.25 inches. A 1.5 kip/ft 6 ft 4 in. h B (a) What are the boundary conditions for this beam? (b) Determine the equation for the moment diagram using statics. (c) Determine the depth of the beam necessary to meet the allowable bending stress requirement.
A leaf spring I m long is made up with steel plates with width equal to 6 times its thickness. Design the spring for a load of 15 kN when the maximum stress is 100 MPa and deflection is not to exceed 16 mm.
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm