4. A homogeneous steel shaft (G=83GPa) is loaded as shown in the above Figure.Assuming T = 361 (N-m)torsional stress in member AB.Note: Include sign in your final answer if negative (-), assuming the direction of Torsion (T) at DispositiveGiven:AB: Length 1.75m, Diameter = 75mmBC: Length = 1.50m, Diameter = 60mmAB: Length = 1.00m, Diameter = 40mmALAT/2determine the maximumBTLAD1200 Nm

Answered: Image /qna-images/answer/24fcc34b-f55e-4aa9-98d6-8f9cfe654a27.jpg

Answered: Assuming T = 361 (N-m) torsional stress…

Engineering

Civil Engineering

Assuming T = 361 (N-m) torsional stress in member AB. determine the maximum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Problem # 4: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and D have a cross-sectional area of 480 mm². For bars B and C, the cross-sectional area is 360 mm². Determine the elongation of bar A when the temperature becomes 60°C. Also, find the axial stress developed in bar C. Use E = 200 GPa and a = 11.7 x 10-6 m/ (m°C). 800 mm D 20 B °8 25000 kg 20 O
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
The copper rod AB and steel rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 17°C, determine the average normal stress in each member when T2 = 47°C. Also, how far will the collar be displaced? The cross-sectional area of each member is 1130 mm?. %3D Сopper Steel Elastic Modulus (GPa) 120 200 Coefficient of thermal expansion (1/°C) 17x10-6 12x10-6 В 1 m 0.6 m-
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi
(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
The stresses acting on an element are dx = 745 psi, ay = 615 psi, and Txy = 430 psi. (Consider only the in-plane stresses the stresses in the x-y-plane). Oy Determine the principal stresses (in psi) and angle of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention. For maximum shear stress, enter the magnitude.) %1 = psi 0₂ = psi psi max = 8p = Show the stresses on a sketch of a properly oriented element. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen This answer has not been graded yet.
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 520 mm?. If the stress in the bar must not exceed 650 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c= 10.4 m. (1) B' a Answer: P = i kN
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.