H.WII Cooling Load Estimation An air conditioned room in the Basra city that measures 3 m wide, 3.5 m high and 6 m deep. The window size 1.5 m*1.5 m, mounted on the wall with no external shading and the door size 2m*1m. Calculate the sensible, latent and total heat gains on the room. What is the required cooling capacity? Assume all specification parameters that must be taken into account when calculating cooling load.

H.WII Cooling Load Estimation An air conditioned room in the Basra city that measures 3 m wide, 3.5 m high and 6 m deep. The window size 1.5 m1.5 m, mounted on the wall with no external shading and the door size 2m1m. Calculate the sensible, latent and total heat gains on the room. What is the required cooling capacity? Assume all specification parameters that must be taken into account when calculating cooling load.

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter8: Direct Use Of Solar Energy

Section: Chapter Questions

Problem 17P

See similar textbooks

Similar questions

For an air-conditioning system, the outdoor and indoor design dry bulb temperatures are 45°C and 25°C respectively. The space to be air-conditioned Is 20m x 30m x 5m and infiltration is estimated to be one alr are 1.2 (kg of dry air)/m³ and 1.02 kJ/(kg of dry air) °C, then the sensible heat load due to Infiltration is, nearly
100°? air flows through a round aluminum tube of ID 60mm and OD 80mm at 4 ?? .The tube is covered in 5mm thick fiberglass insulation. The tube is surrounded by RT air flowing at 5?? over the outside of the insulation. What is the heat rate through the wall of the tube? Assume that the air temperature is constant throughout the tube. Note: RT is 25 celsius
need ans very very fast in 20 min
A well-mixed, insulated water storage tank is to be maintained at internal temperature 60°C. The environmental temperature around the tank varies from -25°C to 30°C. The tank's exterior surfaces (total = 125 m²) have four different levels of insulation as indicated in the table. Surface Component Area, Effective RSI, 2 2 m². °C/W m² Surface A 60.0 Surface B 30.0 Surface C 30.0 Surface D 5.0 Say that just one surface can be selected to have its insulation upgraded such that its effective RSI would be doubled. Which should be selected to achieve the greatest reduction in heat loss? 10.0 15.0 4.0 0.5
Pls. Answer thank you! A room's sensible space load is from occupants and infiltration, but excluding intentional ventilation, is 3.2 kw. A total of 600 L/s of outside air is required. What is most nearly the room sensible heat ratio?
Inside a wall measuring N/Sx N /3m, there are 2(glass thickness lcm) single-glazed windows measuring 1.5 m x 3 m with a heat transfer coefficient of K there is a window. The ambient temperature on the inside of the wall is N20C, the outdoor temperature is - N3 oC, the coefficients of external and internal convection are aş= N W/m2 C, aic = N/3 W/m2 C is. The wall is from the outside to the inside, 0.1N cm. the outer plaster with a thickness of k= 0.3N W/ moC, with a thickness of N/ 2 cm k = 0.8 W/moC reinforced concrete is composed of 1 cm thick k= 0.6 W/m oC gypsum honey inner plaster.Find out the total heat loss. To reduce heat loss by 80%, k= How many cm of insulating(styrofoam) material with an oC of 0.001(N+N2 )W/m should be N=26 used(calculations will be made for single and double glazing. My greatest achievement please heap the required amount of flow before and after it is made N2=9 N3=119
A 100 mm concrete wall is to be used to make a cold storage. The floor and ceiling is to use the same material. The room is supposed to have height of 5 m, length of 7 m and a width of 6 m. The ambient temperature is 36 degrees and the room has to be cooled at 3 degrees. The cold storage is to be used to cool 1600 kg of milk. Conduct the cooling load calculation for the room and determine the cooling capacity of the cooling equipment required for this room. Subject- Civil Engineering Only correct answer
17-A refrigerator is to remove heat from the cooled space at a rate of 300 kJ/min to maintain its temperature at -8°C. Wam in.min REFRIG. 300 25°C -8°C kJ/min
Find the heat load for the following side of a house for a 70°F design temperaturedifference. The wall is a wood frame with siding and 31⁄2 inches of insulation. The windowis double pane.
The damping ratio of the system response shown in BLUE is 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 20 30 40 00.5 01.2 10
1 Ii. In. O O 1:10 O E:10 bgås ui - 2_5271793917405171255 H.W • In an air standard Otto cycle the maximum and minimum temperature are 1400 C and 15 C .the heat supply per Kg of air is 800 Kj .calculate the compression ratio and the thermal efficiency .also the ratio of maximum to minimum pressure في دورة أوتو القياسية للهواء تكون درجة الحرارة العظمی والصغرى 1400 درجة مئوية و 15 درجة مئوية ، ويكون إمداد الحرارة لكل كيلوجرام من الهواء 800 كیلوجول. أحسب نسبة حرارية ، وكذلك نسبة الضغط الأقصي إلى الأدنی PV =C تعلیقات ملاحظات HW + 17 16 15 14 A II >
A steel tube with 5 cm ID, 7.6 cm OD and k=15W/m °C is covered with an insulative covering of thickness 2 cm and k 0.2 W/m °C. A hot gas at 330° C with h = 400 W/m2oC flows inside the tube. The outer surface of the insulation is exposed to cooler air at 30°C with h = 60 W/m2oC. Calculate the heat loss from the tube to the air for 10 m of the tube and the temperature drops resulting from the thermal resistances of the hot gas flow, the steel tube, the insulation layer and the outside air.